VAIL 100D 2 ft. x 10 ft. Frame Only

190

Vail-100D 2’ x 10’ Frame Only. The VAIL-100D is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-100D is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is compatible with edge-lights or ladder lights (can be backlit). 


Frame Includes: 

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (2) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-100D extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 10’ edge and one 2′ edge and slide in Corner Connector; tighten. Repeat this three times. 


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 120″W x 24″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

VAIL 100D 2 ft. x 3 ft. – Double-Sided Graphic Only

189

Double-Sided Graphic Replacement for the Vail-100D 2’ x 3’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.


Graphic Only Includes:

  • (2) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Graphic Installation:Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Warranty: One (1) year on graphics 


Artwork Size: 26″W x 38″H 


Shipping Dimensions: 12″L x 9″W x 6″H 

VAIL 100D 2 ft. x 4 ft. – Double-Sided Graphic Only

188

Double-Sided Graphic Replacement for the Vail-100D 2’ x 4’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.


Graphic Only Includes:

  • (2) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Graphic Installation:Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Warranty: One (1) year on graphics 


Artwork Size:26″W x 50″H 


Shipping Dimensions: 16″L x 10″W x 6″H 


Shipping Weight: 4 lbs

VAIL 100D 2 ft. x 5 ft. – Double-Sided Graphic Only

187

Double-Sided Graphic Replacement for the Vail-100D 2’ x 5’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.


Graphic Only Includes:

  • (2) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Graphic Installation:Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Warranty: One (1) year on graphics 


Artwork Size: 26″W x 62″H 


Shipping Dimensions: 16″L x 10″W x 6″H 


Shipping Weight: 6 lbs

VAIL 100D 2 ft. x 7 ft. – Double-Sided Graphic Only

 

185

Double-Sided Graphic Replacement for the Vail-100D 2’ x 7’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.


Graphic Only Includes:

  • (2) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation 


Graphic Installation:Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Warranty: One (1) year on graphics 


Artwork Size: 26″W x 86″H 


Shipping Dimensions: 20″L x 12″W x 6″H 


Shipping Weight: 6 lbs

VAIL 100D 2 ft. x 6 ft. – Double-Sided Graphic Only

186

Double-Sided Graphic Replacement for the Vail-100D 2’ x 6’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.


Graphic Only Includes:

  • (2) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Graphic Installation:Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 

Warranty: One (1) year on graphics 


Artwork Size: 26″W x 74″H 


Shipping Dimensions: 16″L x 10″W x 6″H 


Shipping Weight: 6 lbs

VAIL 100D 2 ft. x 8 ft. – Double-Sided Graphic Only

184

Double-Sided Graphic Replacement for the Vail-100D 2’ x 8’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.


Graphic Only Includes:

  • (2) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation


Graphic Installation:Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Warranty: One (1) year on graphics 


Artwork Size: 26″W x 98″H 


Shipping Dimensions: 20″L x 12″W x 6″H 


Shipping Weight: 6 lbs

VAIL 100D 2 ft. x 9 ft. – Double-Sided Graphic Only

183

Double-Sided Graphic Replacement for the Vail-100D 2’ x 9’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.


Graphic Only Includes:

  • (2) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Graphic Installation:Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Warranty: One (1) year on graphics 


Artwork Size: 26″W x 110″H 


Shipping Dimensions: 20″L x 16″W x 6″H 


Shipping Weight: 6 lbs

VAIL 100D 2 ft. x 9 ft. Frame Only

182

Vail-100D 2’ x 9’ Frame Only. The VAIL-100D is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-100D is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is compatible with edge-lights or ladder lights (can be backlit). 


Frame Includes:

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (2) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-100D extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 2′ edge and slide in Corner Connector; tighten. Repeat this three times. 


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 24″W x 108″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

VAIL 100D 2 ft. x 9 ft. – Single-Sided Graphic Only

181

Single-Sided Graphic Replacement for the Vail-100D 2’ x 9’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.


Graphic Only Includes:

  • (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Warranty: One (1) year on graphics 


Artwork Size: 26″W x 110″H 


Shipping Dimensions: (1) box 16″L x 12″W x 6″H


Shipping Weight: 3 lbs

VAIL 40D 9 ft. x 10 ft. Double-Sided Graphic Package

180

Vail-40D 9’ x 10’ Double-Sided Graphic Package. The VAIL-40D is a double-sided Resort Extrusion with a profile width of 40mm. The alternative extrusion in style to the ASPEN-40D, the VAIL-40D has a solid outside finish. It is especially great for wall mounting and hanging overhead because it is lightweight, but can be used with feet to stand independently as it is more stable than the VAIL-40S. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.)


Package Includes: 

  • (1) 4-Sided Frame
  • (2) Custom Single-Sided Graphics (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (5) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Backdrop, Photo-ops, Showrooms, Step & Repeat, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Hardware Setup: : To make one edge of the frame, take two cut VAIL-40D extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 10′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 120″H x 1.57″D


Artwork Size: 110″W x 122″H


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H

VAIL 40D 9 ft. x 2 ft. Double-Sided Graphic Package

179

Vail-40D 9’ x 2’ Double-Sided Graphic Package. The VAIL-40D is a double-sided Resort Extrusion with a profile width of 40mm. The alternative extrusion in style to the ASPEN-40D, the VAIL-40D has a solid outside finish. It is especially great for wall mounting and hanging overhead because it is lightweight, but can be used with feet to stand independently as it is more stable than the VAIL-40S. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.) 


Package Includes:

  • (1) 4-Sided Frame
  • (2) Custom Single-Sided Graphics (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions



Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Backdrop, Photo-ops, Showrooms, Step & Repeat, Etc. 


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: : To make one edge of the frame, take two cut VAIL-40D extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 2′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors 


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 24″H x 1.57″D 


Artwork Size: 110″W x 26″H 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

VAIL 40D 9 ft. x 3 ft. Double-Sided Graphic Package

178+

Vail-40D 9’ x 3’ Double-Sided Graphic Package. The VAIL-40D is a double-sided Resort Extrusion with a profile width of 40mm. The alternative extrusion in style to the ASPEN-40D, the VAIL-40D has a solid outside finish. It is especially great for wall mounting and hanging overhead because it is lightweight, but can be used with feet to stand independently as it is more stable than the VAIL-40S. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.) 


Package Includes: 

  • (1) 4-Sided Frame
  • (2) Custom Single-Sided Graphics (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions



Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Backdrop, Photo-ops, Showrooms, Step & Repeat, Etc. 


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: : To make one edge of the frame, take two cut VAIL-40D extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 3′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors 


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 36″H x 1.57″D 


Artwork Size: 110″W x 38″H 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

VAIL 40D 9 ft. x 4 ft. Double-Sided Graphic Package

177

Vail-40D 9’ x 4’ Double-Sided Graphic Package. The VAIL-40D is a double-sided Resort Extrusion with a profile width of 40mm. The alternative extrusion in style to the ASPEN-40D, the VAIL-40D has a solid outside finish. It is especially great for wall mounting and hanging overhead because it is lightweight, but can be used with feet to stand independently as it is more stable than the VAIL-40S. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.) 


Package Includes:

  • (1) 4-Sided Frame
  • (2) Custom Single-Sided Graphics (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Backdrop, Photo-ops, Showrooms, Step & Repeat, Etc. 


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: : To make one edge of the frame, take two cut VAIL-40D extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 4′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors 


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 48″H x 1.57″D 


Artwork Size: 110″W x 50″H 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

VAIL 40D 9 ft. x 5 ft. Double-Sided Graphic Package

176

Vail-40D 9’ x 5’ Double-Sided Graphic Package. The VAIL-40D is a double-sided Resort Extrusion with a profile width of 40mm. The alternative extrusion in style to the ASPEN-40D, the VAIL-40D has a solid outside finish. It is especially great for wall mounting and hanging overhead because it is lightweight, but can be used with feet to stand independently as it is more stable than the VAIL-40S. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.) 


Package Includes:

  • (1) 4-Sided Frame
  • (2) Custom Single-Sided Graphics (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions



Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Backdrop, Photo-ops, Showrooms, Step & Repeat, Etc. 


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: : To make one edge of the frame, take two cut VAIL-40D extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 5′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors 


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 60″H x 1.57″D 


Artwork Size: 110″W x 62″H 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H

VAIL 40D 9 ft. x 6 ft. Double-Sided Graphic Package

175

Vail-40D 9’ x 6’ Double-Sided Graphic Package. The VAIL-40D is a double-sided Resort Extrusion with a profile width of 40mm. The alternative extrusion in style to the ASPEN-40D, the VAIL-40D has a solid outside finish. It is especially great for wall mounting and hanging overhead because it is lightweight, but can be used with feet to stand independently as it is more stable than the VAIL-40S. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.) 


Package Includes:

  • (1) 4-Sided Frame
  • (2) Custom Single-Sided Graphics (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Backdrop, Photo-ops, Showrooms, Step & Repeat, Etc. 


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: : To make one edge of the frame, take two cut VAIL-40D extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 6′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors 


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 72″H x 1.57″D 


Artwork Size: 110″W x 74″H 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H

VAIL 40D 9 ft. x 8 ft. Double-Sided Graphic Package

173

Vail-40D 9’ x 8’ Double-Sided Graphic Package. The VAIL-40D is a double-sided Resort Extrusion with a profile width of 40mm. The alternative extrusion in style to the ASPEN-40D, the VAIL-40D has a solid outside finish. It is especially great for wall mounting and hanging overhead because it is lightweight, but can be used with feet to stand independently as it is more stable than the VAIL-40S. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.) 


Package Includes:

  • (1) 4-Sided Frame
  • (2) Custom Single-Sided Graphics (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions



Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Backdrop, Photo-ops, Showrooms, Step & Repeat, Etc. 


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: : To make one edge of the frame, take two cut VAIL-40D extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 8′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors 


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 96″H x 1.57″D 


Artwork Size: 110″W x 98″H 


Shipping Dimensions: (2) boxes 96″L x 7.25″W x 6.5″H & 73.25″L x 7.25″W x 6.5″H

VAIL 40D 9 ft. x 7 ft. Double-Sided Graphic Package

174

Vail-40D 9’ x 7’ Double-Sided Graphic Package. The VAIL-40D is a double-sided Resort Extrusion with a profile width of 40mm. The alternative extrusion in style to the ASPEN-40D, the VAIL-40D has a solid outside finish. It is especially great for wall mounting and hanging overhead because it is lightweight, but can be used with feet to stand independently as it is more stable than the VAIL-40S. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.)


Package Includes:

  • (1) 4-Sided Frame
  • (2) Custom Single-Sided Graphics (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Backdrop, Photo-ops, Showrooms, Step & Repeat, Etc. 


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: : To make one edge of the frame, take two cut VAIL-40D extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 7′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors 


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 84″H x 1.57″D 


Artwork Size: 110″W x 86″H 


Shipping Dimensions: (2) boxes 96″L x 7.25″W x 6.5″H & 73.25″L x 7.25″W x 6.5″H

VAIL 40D 9 ft. x 9 ft. Double-Sided Graphic Package

178

Vail-40D 9’ x 9’ Double-Sided Graphic Package. The VAIL-40D is a double-sided Resort Extrusion with a profile width of 40mm. The alternative extrusion in style to the ASPEN-40D, the VAIL-40D has a solid outside finish. It is especially great for wall mounting and hanging overhead because it is lightweight, but can be used with feet to stand independently as it is more stable than the VAIL-40S. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.) 


Package Includes:

  • (1) 4-Sided Frame
  • (2) Custom Single-Sided Graphic (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (5) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions



Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Step & Repeat, Etc. 


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation


Hardware Setup: : To make one edge of the frame, take two cut VAIL-40D extrusions and, between, add Split Connector; tighten. Repeat this three times. Take two completed 9’ edges and slide in Corner Connector; tighten. Repeat this three times. Connect VAIL-40C to the other; tighten. Vertically insert ends of completed VAIL-40C into top and bottom of the frame; tighten. 


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 108″H x 1.57″D


Artwork Size: 110″W x 110″H


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H

9 ft. VAIL 60S – 3’h (Frame Only)

171

Vail-60S  9’ x 3’ Frame Only. The VAIL-60S  is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Frame Includes: 

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 3′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 108″W x 36″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

9 ft. VAIL 60S – 3’h Single-Sided Graphic Only

170

Single-Sided Graphic Replacement for the Vail-60S 9’ x 3’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

 

Graphic Only Includes:

  • (1) Custom Single-Sided Graphic with SEG hem

 

Material: Deco Fabric (non-stretch)

 

Print Process: Full Color Dye Sublimation

 

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

 

Warranty: One (1) year on graphics

 

Artwork Size: 110″W x 38″H

 

Shipping Dimensions: (1) box 16″L x 12″W x 6″H

 

Shipping Weight: 4 lbs

9 ft. VAIL 60S – 2’h (Frame Only)

169

Vail-60S  9’ x 2’ Frame Only. The VAIL-60S  is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Frame Includes: 

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 2′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 108″W x 24″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

9 ft. VAIL 60S – 4’h (Frame Only)

168

Vail-60S  9’ x 4’ Frame Only. The VAIL-60S  is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Frame Includes: 

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 4′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 108″W x 48″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

9 ft. VAIL 60S – 5’h (Frame Only)

167

Vail-60S  9’ x 5’ Frame Only. The VAIL-60S  is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Frame Includes: 

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 5′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 108″W x 60″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

9 ft. VAIL 60S – 6’h (Frame Only)

166

Vail-60S  9’ x 6’ Frame Only. The VAIL-60S  is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Frame Includes: 

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 6′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 108″W x 72″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

9 ft. VAIL 60S – 7’h (Frame Only)

165

Vail-60S  9’ x 7’ Frame Only. The VAIL-60S  is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Frame Includes: 

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 7′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 108″W x 84″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

9 ft. VAIL 60S – 8’h (Frame Only)

164

Vail-60S  9’ x 8’ Frame Only. The VAIL-60S  is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Frame Includes: 

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 8′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 108″W x 84″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

9 ft. VAIL 60S – 9’h (Frame Only)

163

Vail-60S  9’ x 9’ Frame Only. The VAIL-60S  is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Frame Includes: 

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (5) VAIL Split Connectors (1 installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 9′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 108″W x 108″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

9 ft. VAIL 60S – 10’h (Frame Only)

162

Vail-60S  9’ x 10’ Frame Only. The VAIL-60S  is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Frame Includes: 

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (5) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 10′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 108″W x 120″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

9 ft. VAIL 60S – 2’h Single-Sided Graphic Package

161

Vail-60S 9’ x 2’ Single-Sided Graphic Package. Vail-60S  is a double-sided Resort Extrusion with a 60mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Package Includes:

  • (1) 4-Sided Frame
  • (1) Custom Single-Sided Graphic (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Partition Wall, Step & Repeat, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Hardware Setup: : To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 2’ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 24″H x 3.94″D


Artwork Size: 110″W x 38″H


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

9 ft. VAIL 60S – 4’h Single-Sided Graphic Package

160

Vail-60S 9’ x 4’ Single-Sided Graphic Package. Vail-60S  is a double-sided Resort Extrusion with a 60mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Package Includes:

  • (1) 4-Sided Frame
  • (1) Custom Single-Sided Graphic (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Partition Wall, Step & Repeat, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Hardware Setup: : To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 4’ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 48″H x 3.94″D


Artwork Size: 110″W x 38″H


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

9 ft. VAIL 60S – 6’h Single-Sided Graphic Package

159

Vail-60S 9’ x 6’ Single-Sided Graphic Package. Vail-60S  is a double-sided Resort Extrusion with a 60mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Package Includes:

  • (1) 4-Sided Frame
  • (1) Custom Single-Sided Graphic (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Partition Wall, Step & Repeat, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Hardware Setup: : To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 6’ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 72″H x 3.94″D


Artwork Size: 110″W x 38″H


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

9 ft. VAIL 60S – 8’h Single-Sided Graphic Package

157

Vail-60S 9’ x 8’ Single-Sided Graphic Package. Vail-60S  is a double-sided Resort Extrusion with a 60mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Package Includes:

  • (1) 4-Sided Frame
  • (1) Custom Single-Sided Graphic (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Partition Wall, Step & Repeat, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Hardware Setup: : To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 8’ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 96″H x 3.94″D


Artwork Size: 110″W x 38″H


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

9 ft. VAIL 60S – 7’h Single-Sided Graphic Package

158

Vail-60S 9’ x 7’ Single-Sided Graphic Package. Vail-60S  is a double-sided Resort Extrusion with a 60mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Package Includes:

  • (1) 4-Sided Frame
  • (1) Custom Single-Sided Graphic (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Partition Wall, Step & Repeat, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Hardware Setup: : To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 7’ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 84″H x 3.94″D


Artwork Size: 110″W x 38″H


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

9 ft. VAIL 60S – 9’h Single-Sided Graphic Package

156

Vail-60S 9’ x 9’ Single-Sided Graphic Package. Vail-60S  is a double-sided Resort Extrusion with a 60mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Package Includes:

  • (1) 4-Sided Frame
  • (1) Custom Single-Sided Graphic (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (5) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Partition Wall, Step & Repeat, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Hardware Setup: : To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 9’ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 108″H x 3.94″D


Artwork Size: 110″W x 38″H


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

9 ft. VAIL 60S – 10’h Single-Sided Graphic Package

155

Vail-60S 9’ x 10’ Single-Sided Graphic Package. Vail-60S  is a double-sided Resort Extrusion with a 60mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Package Includes:

  • (1) 4-Sided Frame
  • (1) Custom Single-Sided Graphic (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (5) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Partition Wall, Step & Repeat, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Hardware Setup: : To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 10’ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 120″H x 3.94″D


Artwork Size: 110″W x 38″H


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

9 ft. VAIL 60S – 2’h Single-Sided Graphic Only

154

Single-Sided Graphic Replacement for the Vail-60S 9’ x 2’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

 

Graphic Only Includes:

  • (1) Custom Single-Sided Graphic with SEG hem

 

Material: Deco Fabric (non-stretch)

 

Print Process: Full Color Dye Sublimation

 

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

 

Warranty: One (1) year on graphics

 

Artwork Size: 110″W x 26″H

 

Shipping Dimensions: (1) box 16″L x 12″W x 6″H

 

Shipping Weight: 4 lbs

 

9 ft. VAIL 60S – 4’h Single-Sided Graphic Only

153

Single-Sided Graphic Replacement for the Vail-60S 9’ x 4’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

 

Graphic Only Includes:

  • (1) Custom Single-Sided Graphic with SEG hem

 

Material: Deco Fabric (non-stretch)

 

Print Process: Full Color Dye Sublimation

 

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

 

Warranty: One (1) year on graphics

 

Artwork Size: 110″W x 50″H

 

Shipping Dimensions: (1) box 16″L x 12″W x 6″H

 

Shipping Weight: 4 lbs

9 ft. VAIL 60S – 5’h Single-Sided Graphic Only

152

Single-Sided Graphic Replacement for the Vail-60S 9’ x 5’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

 

Graphic Only Includes:

  • (1) Custom Single-Sided Graphic with SEG hem

 

Material: Deco Fabric (non-stretch)

 

Print Process: Full Color Dye Sublimation

 

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

 

Warranty: One (1) year on graphics

 

Artwork Size: 110″W x 62″H

 

Shipping Dimensions: (1) box 16″L x 12″W x 6″H

 

Shipping Weight: 4 lbs

9 ft. VAIL 60S – 6’h Single-Sided Graphic Only

151

Single-Sided Graphic Replacement for the Vail-60S 9’ x 6’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

 

Graphic Only Includes:

  • (1) Custom Single-Sided Graphic with SEG hem

 

Material: Deco Fabric (non-stretch)

 

Print Process: Full Color Dye Sublimation

 

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

 

Warranty: One (1) year on graphics

 

Artwork Size: 110″W x 74″H

 

Shipping Dimensions: (1) box 16″L x 12″W x 6″H

 

Shipping Weight: 4 lbs

9 ft. VAIL 60S – 7’h Single-Sided Graphic Only

150

Single-Sided Graphic Replacement for the Vail-60S 9’ x 7’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

 

Graphic Only Includes:

  • (1) Custom Single-Sided Graphic with SEG hem

 

Material: Deco Fabric (non-stretch)

 

Print Process: Full Color Dye Sublimation

 

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

 

Warranty: One (1) year on graphics

 

Artwork Size: 110″W x 86″H

 

Shipping Dimensions: (1) box 16″L x 12″W x 6″H

 

Shipping Weight: 4 lbs

 

9 ft. VAIL 60S – 8’h Single-Sided Graphic Only

149

Single-Sided Graphic Replacement for the Vail-60S 9’ x 8’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

 

Graphic Only Includes:

  • (1) Custom Single-Sided Graphic with SEG hem

 

Material: Deco Fabric (non-stretch)

 

Print Process: Full Color Dye Sublimation

 

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

 

Warranty: One (1) year on graphics

 

Artwork Size: 110″W x 98″H

 

Shipping Dimensions: (1) box 16″L x 12″W x 6″H

 

Shipping Weight: 4 lbs

9 ft. VAIL 60S – 9’h Single-Sided Graphic Only

148

Single-Sided Graphic Replacement for the Vail-60S 9’ x 9’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

 

Graphic Only Includes:

  • (1) Custom Single-Sided Graphic with SEG hem

 

Material: Deco Fabric (non-stretch)

 

Print Process: Full Color Dye Sublimation

 

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

 

Warranty: One (1) year on graphics

 

Artwork Size: 110″W x 110″H

 

Shipping Dimensions: (1) box 16″L x 12″W x 6″H

 

Shipping Weight: 4 lbs

9 ft. VAIL 60S – 10’h Single-Sided Graphic Only

147

Single-Sided Graphic Replacement for the Vail-60S 9’ x 10’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

 

Graphic Only Includes:

  • (1) Custom Single-Sided Graphic with SEG hem

 

Material: Deco Fabric (non-stretch)

 

Print Process: Full Color Dye Sublimation

 

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

 

Warranty: One (1) year on graphics

 

Artwork Size: 110″W x 122″H

 

Shipping Dimensions: (1) box 16″L x 12″W x 6″H

 

Shipping Weight: 4 lbs

10 ft. VAIL 60S – 2’h (Frame Only)

146

Vail-60S  10’ x 2’ Frame Only. The VAIL-60S  is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Frame Includes: 

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 10’ edge and one 2′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 120″W x 24″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

10 ft. VAIL 60S – 3’h (Frame Only)

145

Vail-60S  10’ x 3’ Frame Only. The VAIL-60S  is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Frame Includes: 

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 10’ edge and one 3′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 120″W x 36″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

10 ft. VAIL 60S – 4’h (Frame Only)

144

Vail-60S  10’ x 4’ Frame Only. The VAIL-60S  is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Frame Includes: 

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 10’ edge and one 4′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 120″W x 48″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

10 ft. VAIL 60S – 5’h (Frame Only)

143

Vail-60S  10’ x 5’ Frame Only. The VAIL-60S  is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Frame Includes: 

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 10’ edge and one 5′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 120″W x 60″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

10 ft. VAIL 60S – 6’h (Frame Only)

142
Vail-60S  10’ x 6’ Frame Only. The VAIL-60S  is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Frame Includes: 

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 10’ edge and one 6′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 120″W x 72″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

10 ft. VAIL 60S – 7’h (Frame Only)

141

Vail-60S  10’ x 7’ Frame Only. The VAIL-60S  is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Frame Includes: 

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 10’ edge and one 7′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 108″W x 84″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

10 ft. VAIL 60S – 8’h (Frame Only)

140

Vail-60S  10’ x 8’ Frame Only. The VAIL-60S  is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Frame Includes: 

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 10’ edge and one 8′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 108″W x 84″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

10 ft. VAIL 60S – 9’h (Frame Only)

139

Vail-60S  10’ x 9’ Frame Only. The VAIL-60S  is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Frame Includes: 

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (5) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 10’ edge and one 9′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 120″W x 108″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

10 ft. VAIL 60S – 10’h (Frame Only)

138

Vail-60S  10’ x 10’ Frame Only. The VAIL-60S  is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Frame Includes: 

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (5) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 10’ edge and one 10′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 120″W x 120″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

10 ft. VAIL 60S – 2’h Single-Sided Graphic Only

137

Single-Sided Graphic Replacement for the Vail-60S 10’ x 2’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Graphic Only Includes:

  • (1) Custom Single-Sided Graphic with SEG hem
  • Material: Deco Fabric (non-stretch)

Print Process: Full Color Dye Sublimation

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

Warranty: One (1) year on graphics

Artwork Size: 122″W x 26″H

Shipping Dimensions: (1) box 16″L x 12″W x 6″H
Shipping Weight: 4 lbs

10 ft. VAIL 60S – 3’h Single-Sided Graphic Only

136

Single-Sided Graphic Replacement for the Vail-60S 10’ x 3’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

 

Graphic Only Includes:

  • (1) Custom Single-Sided Graphic with SEG hem

 

Material: Deco Fabric (non-stretch)

 

Print Process: Full Color Dye Sublimation

 

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

 

Warranty: One (1) year on graphics

 

Artwork Size: 122″W x 38″H

 

Shipping Dimensions: (1) box 16″L x 12″W x 6″H

 

Shipping Weight: 4 lbs

 

10 ft. VAIL 60S – 4’h Single-Sided Graphic Only

135

Single-Sided Graphic Replacement for the Vail-60S 10’ x 4’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

 

Graphic Only Includes:

  • (1) Custom Single-Sided Graphic with SEG hem

 

Material: Deco Fabric (non-stretch)

 

Print Process: Full Color Dye Sublimation

 

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

 

Warranty: One (1) year on graphics

 

Artwork Size: 122″W x 50″H

 

Shipping Dimensions: (1) box 16″L x 12″W x 6″H

 

Shipping Weight: 4 lbs

10 ft. VAIL 60S – 6’h Single-Sided Graphic Only

133

Single-Sided Graphic Replacement for the Vail-60S 10’ x 6’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

 

Graphic Only Includes:

  • (1) Custom Single-Sided Graphic with SEG hem

 

Material: Deco Fabric (non-stretch)

 

Print Process: Full Color Dye Sublimation

 

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

 

Warranty: One (1) year on graphics

 

Artwork Size: 122″W x 74″H

 

Shipping Dimensions: (1) box 16″L x 12″W x 6″H

 

Shipping Weight: 4 lbs

10 ft. VAIL 60S – 5’h Single-Sided Graphic Only

134

Single-Sided Graphic Replacement for the Vail-60S 10’ x 5’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

 

Graphic Only Includes:

  • (1) Custom Single-Sided Graphic with SEG hem

 

Material: Deco Fabric (non-stretch)

 

Print Process: Full Color Dye Sublimation

 

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

 

Warranty: One (1) year on graphics

 

Artwork Size: 122″W x 62″H

 

Shipping Dimensions: (1) box 16″L x 12″W x 6″H

 

Shipping Weight: 4 lbs

10 ft. VAIL 60S – 7’h Single-Sided Graphic Only

132

Single-Sided Graphic Replacement for the Vail-60S 10’ x 7’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

 

Graphic Only Includes:

  • (1) Custom Single-Sided Graphic with SEG hem

 

Material: Deco Fabric (non-stretch)

 

Print Process: Full Color Dye Sublimation

 

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

 

Warranty: One (1) year on graphics

 

Artwork Size: 122″W x 86″H

 

Shipping Dimensions: (1) box 16″L x 12″W x 6″H

 

Shipping Weight: 4 lbs

 

10 ft. VAIL 60S – 8’h Single-Sided Graphic Only

131

Single-Sided Graphic Replacement for the Vail-60S 10’ x 8’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

 

Graphic Only Includes:

  • (1) Custom Single-Sided Graphic with SEG hem

 

Material: Deco Fabric (non-stretch)

 

Print Process: Full Color Dye Sublimation

 

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

 

Warranty: One (1) year on graphics

 

Artwork Size: 122″W x 98″H

 

Shipping Dimensions: (1) box 16″L x 12″W x 6″H

 

Shipping Weight: 4 lbs

 

10 ft. VAIL 60S – 9’h Single-Sided Graphic Only

130

Single-Sided Graphic Replacement for the Vail-60S 10’ x 9’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

 

Graphic Only Includes:

  • (1) Custom Single-Sided Graphic with SEG hem

 

Material: Deco Fabric (non-stretch)

 

Print Process: Full Color Dye Sublimation

 

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

 

Warranty: One (1) year on graphics

 

Artwork Size: 122″W x 110″H

 

Shipping Dimensions: (1) box 16″L x 12″W x 6″H

 

Shipping Weight: 4 lbs

10 ft. VAIL 60S – 10’h Single-Sided Graphic Only

129

Single-Sided Graphic Replacement for the Vail-60S 10’ x 10’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

 

Graphic Only Includes:

  • (1) Custom Single-Sided Graphic with SEG hem

 

Material: Deco Fabric (non-stretch)

 

Print Process: Full Color Dye Sublimation

 

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

 

Warranty: One (1) year on graphics

 

Artwork Size: 122″W x 122″H

 

Shipping Dimensions: (1) box 16″L x 12″W x 6″H

 

Shipping Weight: 4 lbs

10 ft. VAIL 60S – 2’h Single-Sided Graphic Package

128

Vail-60S 10’ x 2’ Single-Sided Graphic Package. Vail-60S  is a double-sided Resort Extrusion with a 60mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).

Package Includes:

  • (1) 4-Sided Frame
  • (1) Custom Single-Sided Graphic (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions
  • Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices,
  • Showrooms, Backdrop, Photo-ops, Partition Wall, Step & Repeat, Etc.

Material: Deco Fabric (non-stretch)

Print Process: Full Color Dye Sublimation

Hardware Setup: : To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 10’ edge and one 2’ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.

Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.

Warranty: Lifetime on frame; one (1) year on graphics

Frame Size: 108″W x 24″H x 3.94″D

Artwork Size: 122″W x 38″H

Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

10 ft. VAIL 60S – 4’h Single-Sided Graphic Package

127

Vail-60S 10’ x 4’ Single-Sided Graphic Package. Vail-60S  is a double-sided Resort Extrusion with a 60mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Package Includes:

  • (1) 4-Sided Frame
  • (1) Custom Single-Sided Graphic (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Partition Wall, Step & Repeat, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Hardware Setup: : To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 10’ edge and one 4’ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 120″W x 48″H x 3.94″D


Artwork Size: 122″W x 38″H


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

10 ft. VAIL 60S – 5’h Single-Sided Graphic Package

126

Vail-60S 10’ x 5’ Single-Sided Graphic Package. Vail-60S  is a double-sided Resort Extrusion with a 60mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Package Includes:

  • (1) 4-Sided Frame
  • (1) Custom Single-Sided Graphic (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Partition Wall, Step & Repeat, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Hardware Setup: : To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 10’ edge and one 5’ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 120″W x 60″H x 3.94″D


Artwork Size: 122″W x 38″H


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

10 ft. VAIL 60S – 6’h Single-Sided Graphic Package

125

Vail-60S 10’ x 6’ Single-Sided Graphic Package. Vail-60S  is a double-sided Resort Extrusion with a 60mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Package Includes:

  • (1) 4-Sided Frame
  • (1) Custom Single-Sided Graphic (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Partition Wall, Step & Repeat, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Hardware Setup: : To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 10’ edge and one 6’ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 120″W x 72″H x 3.94″D


Artwork Size: 122″W x 38″H


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

10 ft. VAIL 60S – 7’h Single-Sided Graphic Package

124

Vail-60S 10’ x 7’ Single-Sided Graphic Package. Vail-60S  is a double-sided Resort Extrusion with a 60mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Package Includes:

  • (1) 4-Sided Frame
  • (1) Custom Single-Sided Graphic (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Partition Wall, Step & Repeat, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Hardware Setup: : To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 10’ edge and one 7’ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 84″H x 3.94″D


Artwork Size: 110″W x 38″H


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

10 ft. VAIL 60S – 8’h Single-Sided Graphic Package

123

Vail-60S 10’ x 8’ Single-Sided Graphic Package. Vail-60S  is a double-sided Resort Extrusion with a 60mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Package Includes:

  • (1) 4-Sided Frame
  • (1) Custom Single-Sided Graphic (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Partition Wall, Step & Repeat, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Hardware Setup: : To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 10’ edge and one 8’ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 120″W x 96″H x 3.94″D


Artwork Size: 122″W x 38″H


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

10 ft. VAIL 60S – 10’h Single-Sided Graphic Package

121

Vail-60S 10’ x 10’ Single-Sided Graphic Package. Vail-60S  is a double-sided Resort Extrusion with a 60mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Package Includes:

  • (1) 4-Sided Frame
  • (1) Custom Single-Sided Graphic (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (5) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Partition Wall, Step & Repeat, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Hardware Setup: : To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 10’ edge and one 10’ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 120″H x 3.94″D


Artwork Size: 110″W x 38″H


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

10 ft. VAIL 60S – 9’h Single-Sided Graphic Package

122

Vail-60S 10’ x 9’ Single-Sided Graphic Package. Vail-60S  is a double-sided Resort Extrusion with a 60mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Package Includes:

  • (1) 4-Sided Frame
  • (1) Custom Single-Sided Graphic (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
  • (5) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
  • (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
  • (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Partition Wall, Step & Repeat, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Hardware Setup: : To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 10’ edge and one 9’ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 120″W x 108″H x 3.94″D


Artwork Size: 122″W x 38″H


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

VAIL 60S 2 ft. x 9 ft. Single-Sided Graphic Package

120

VAIL-60S 2’ x 9’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-60S is a single-sided extrusion with a profile width of 60mm. The VAIL-60S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).


Package Includes:

  • (1) 4-Sided Frame
  • (1) Custom Single-Sided Graphic (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-60S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 24″W x 108″H x 2.36″D 


Artwork Size: 26″W x 108″H 


Shipping Dimensions:(1) box 96″L x 7.25″W x 6.5″H

VAIL 60S 2 ft. x 9 ft. – Single-Sided Graphic Only

119

Single-Sided Graphic Replacement for the Vail-60S 2’ x 9’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

 

Graphic Only Includes:

  • (1) Custom Single-Sided Graphic with SEG hem

 

Material: Deco Fabric (non-stretch)

 

Print Process: Full Color Dye Sublimation

 

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

 

Warranty: One (1) year on graphics

 

Artwork Size: 26″W x 108″H

 

Shipping Dimensions: 16″L x 10″W x 6″H

 

Shipping Weight: 3 lbs

VAIL 60S 2 ft. x 10 ft. Single-Sided Graphic Package

117

VAIL-60S 2’ x 10’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-60S is a single-sided extrusion with a profile width of 60mm. The VAIL-60S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).


Package Includes:

  • (1) 4-Sided Frame
  • (1) Custom Single-Sided Graphic (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-60S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 24″W x 120″H x 2.36″D 


Artwork Size: 26″W x 120″H 


Shipping Dimensions:(1) box 96″L x 7.25″W x 6.5″H

VAIL 60S 2 ft. x 9 ft. Frame Only

118

Vail-60S 2′ x 9′ Frame Only. The VAIL-60S is a single-sided extrusion with a profile width of 60mm and has a solid outside finish. Because the back side of the VAIL-60S is short, it works especially well for wall mounting letting you affix the frame in multiple ways; however, the VAIL-60S is suitable for free-standing or hanging overhead as well. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).

Frame Includes:

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

 

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.

Hardware Setup: Take two VAIL-60S extrusions and slide ein Corner Connector; tighten. Repeat this three times.
Upgrade to Replace: VAIL Toolless Corner Connector

Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.

Warranty: Lifetime on frame

Frame Size: 24″W x 108″H x 2.36″D

Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

 

VAIL 60S 2 ft. x 10 ft. – Single-Sided Graphic Only

116

Single-Sided Graphic Replacement for the Vail-60S 2’ x 10’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

 

Graphic Only Includes:

  • (1) Custom Single-Sided Graphic with SEG hem

 

Material: Deco Fabric (non-stretch)

 

Print Process: Full Color Dye Sublimation

 

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

 

Warranty: One (1) year on graphics

 

Artwork Size: 26″W x 120″H

 

Shipping Dimensions: 16″L x 10″W x 6″H

 

Shipping Weight: 3 lbs

VAIL 60S 2 ft. x 10 ft. Frame Only

115

Vail-60S 2′ x 10′ Frame Only. The VAIL-60S is a single-sided extrusion with a profile width of 60mm and has a solid outside finish. Because the back side of the VAIL-60S is short, it works especially well for wall mounting letting you affix the frame in multiple ways; however, the VAIL-60S is suitable for free-standing or hanging overhead as well. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).

Frame Includes:

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

 

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.

Hardware Setup: Take two VAIL-60S extrusions and slide ein Corner Connector; tighten. Repeat this three times.
Upgrade to Replace: VAIL Toolless Corner Connector

Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.

Warranty: Lifetime on frame

Frame Size: 24″W x 108″H x 2.36″D

Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

VAIL 60S 3 ft. x 9 ft. – Single-Sided Graphic Only

114

Single-Sided Graphic Replacement for the Vail-60S 3’ x 9’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

 

Graphic Only Includes:

  • (1) Custom Single-Sided Graphic with SEG hem

 

Material: Deco Fabric (non-stretch)

 

Print Process: Full Color Dye Sublimation

 

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

 

Warranty: One (1) year on graphics

 

Artwork Size: 38″W x 108″H

 

Shipping Dimensions: 16″L x 10″W x 6″H

 

Shipping Weight: 3 lbs

VAIL 60S 3 ft. x 9 ft. Frame Only

113

Vail-60S 3′ x 9′ Frame Only. The VAIL-60S is a single-sided extrusion with a profile width of 60mm and has a solid outside finish. Because the back side of the VAIL-60S is short, it works especially well for wall mounting letting you affix the frame in multiple ways; however, the VAIL-60S is suitable for free-standing or hanging overhead as well. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).

Frame Includes:

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

 

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.

Hardware Setup: Take two VAIL-60S extrusions and slide ein Corner Connector; tighten. Repeat this three times.
Upgrade to Replace: VAIL Toolless Corner Connector

Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.

Warranty: Lifetime on frame

Frame Size: 36″W x 108″H x 2.36″D

Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

 

VAIL 60S 3 ft. x 10 ft. – Single-Sided Graphic Only

112

Single-Sided Graphic Replacement for the Vail-60S 3’ x 10’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

 

Graphic Only Includes:

  • (1) Custom Single-Sided Graphic with SEG hem

 

Material: Deco Fabric (non-stretch)

 

Print Process: Full Color Dye Sublimation

 

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

 

Warranty: One (1) year on graphics

 

Artwork Size: 38″W x 120″H

 

Shipping Dimensions: 16″L x 10″W x 6″H

 

Shipping Weight: 3 lbs

VAIL 60S 3 ft. x 10 ft. Frame Only

V11

Vail-60S 3′ x 10′ Frame Only. The VAIL-60S is a single-sided extrusion with a profile width of 60mm and has a solid outside finish. Because the back side of the VAIL-60S is short, it works especially well for wall mounting letting you affix the frame in multiple ways; however, the VAIL-60S is suitable for free-standing or hanging overhead as well. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).

Frame Includes:

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

 

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.

Hardware Setup: Take two VAIL-60S extrusions and slide ein Corner Connector; tighten. Repeat this three times.
Upgrade to Replace: VAIL Toolless Corner Connector

Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.

Warranty: Lifetime on frame

Frame Size: 36″W x 120″H x 2.36″D

Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

VAIL 60S 4 ft. x 10 ft. Single-Sided Graphic Package

110

VAIL-60S 4’ x 10’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-60S is a single-sided extrusion with a profile width of 60mm. The VAIL-60S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).


Package Includes:

  • (1) 4-Sided Frame
  • (1) Custom Single-Sided Graphic (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-60S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 48″W x 72″H x 2.36″D 


Artwork Size: 50″W x 98″H 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

VAIL 60S 4 ft. x 10 ft. – Single-Sided Graphic Only

109

Single-Sided Graphic Replacement for the Vail-60S 4’ x 10’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

 

Graphic Only Includes:

  • (1) Custom Single-Sided Graphic with SEG hem

 

Material: Deco Fabric (non-stretch)

 

Print Process: Full Color Dye Sublimation

 

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

 

Warranty: One (1) year on graphics

 

Artwork Size:50″W x 120″H

 

Shipping Dimensions: 16″L x 12″W x 6″H

 

Shipping Weight: 4 lbs

VAIL 60S 4 ft. x 10 ft. Frame Only

108

Vail-60S 4′ x 10′ Frame Only. The VAIL-60S is a single-sided extrusion with a profile width of 60mm and has a solid outside finish. Because the back side of the VAIL-60S is short, it works especially well for wall mounting letting you affix the frame in multiple ways; however, the VAIL-60S is suitable for free-standing or hanging overhead as well. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).

Frame Includes:

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

 

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.

Hardware Setup: Take two VAIL-60S extrusions and slide ein Corner Connector; tighten. Repeat this three times.
Upgrade to Replace: VAIL Toolless Corner Connector

Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.

Warranty: Lifetime on frame

Frame Size: 48″W x 120″H x 2.36″D

Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

VAIL 60S 5 ft. x 9 ft. Single-Sided Graphic Package

107

VAIL-60S 5′ x 9’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-60S is a single-sided extrusion with a profile width of 60mm. The VAIL-60S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).


Package Includes:

  • (1) 4-Sided Frame
  • (1) Custom Single-Sided Graphic (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-60S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 60″W x 108″H x 2.36″D 


Artwork Size: 62″W x 110″H 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

VAIL 60S 5 ft. x 9 ft. – Single-Sided Graphic Only

106

Single-Sided Graphic Replacement for the Vail-60S 5’ x 9’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

 

Graphic Only Includes:

  • (1) Custom Single-Sided Graphic with SEG hem

 

Material: Deco Fabric (non-stretch)

 

Print Process: Full Color Dye Sublimation

 

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

 

Warranty: One (1) year on graphics

 

Artwork Size:62″W x 110″H

 

Shipping Dimensions: 20″L x 10″W x 6″H

 

Shipping Weight:4 lbs

VAIL 60S 4 ft. x 9 ft. Single-Sided Graphic Package

105

VAIL-60S 4’ x 9’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-60S is a single-sided extrusion with a profile width of 60mm. The VAIL-60S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).


Package Includes:

  • (1) 4-Sided Frame
  • (1) Custom Single-Sided Graphic (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-60S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 48″W x 108″H x 2.36″D 


Artwork Size: 50″W x 110″H 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

VAIL 60S 4 ft. x 9 ft. – Single-Sided Graphic Only

104

Single-Sided Graphic Replacement for the Vail-60S 4’ x 9’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

 

Graphic Only Includes:

  • (1) Custom Single-Sided Graphic with SEG hem

 

Material: Deco Fabric (non-stretch)

 

Print Process: Full Color Dye Sublimation

 

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

 

Warranty: One (1) year on graphics

 

Artwork Size:50″W x 110″H

 

Shipping Dimensions: 16″L x 12″W x 6″H

 

Shipping Weight: 4 lbs

VAIL 60S 4 ft. x 9 ft. Frame Only

103

Vail-60S 4′ x 9′ Frame Only. The VAIL-60S is a single-sided extrusion with a profile width of 60mm and has a solid outside finish. Because the back side of the VAIL-60S is short, it works especially well for wall mounting letting you affix the frame in multiple ways; however, the VAIL-60S is suitable for free-standing or hanging overhead as well. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).

Frame Includes:

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

 

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.

Hardware Setup: Take two VAIL-60S extrusions and slide ein Corner Connector; tighten. Repeat this three times.
Upgrade to Replace: VAIL Toolless Corner Connector

Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.

Warranty: Lifetime on frame

Frame Size: 48″W x 108″H x 2.36″D

Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

VAIL 60S 5 ft. x 10 ft. Single-Sided Graphic Package

101

VAIL-60S 5′ x 10’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-60S is a single-sided extrusion with a profile width of 60mm. The VAIL-60S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).


Package Includes:

  • (1) 4-Sided Frame
  • (1) Custom Single-Sided Graphic (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-60S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 60″W x 120″H x 2.36″D 


Artwork Size: 62″W x 110″H 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

VAIL 60S 5 ft. x 9 ft. Frame Only

102

Vail-60S 5′ x 9′ Frame Only. The VAIL-60S is a single-sided extrusion with a profile width of 60mm and has a solid outside finish. Because the back side of the VAIL-60S is short, it works especially well for wall mounting letting you affix the frame in multiple ways; however, the VAIL-60S is suitable for free-standing or hanging overhead as well. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).

Frame Includes:

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

 

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.

Hardware Setup: Take two VAIL-60S extrusions and slide ein Corner Connector; tighten. Repeat this three times.
Upgrade to Replace: VAIL Toolless Corner Connector

Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.

Warranty: Lifetime on frame

Frame Size: 60″W x 108″H x 2.36″D

Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

VAIL 60S 5 ft. x 10 ft. – Single-Sided Graphic Only

V100

Single-Sided Graphic Replacement for the Vail-60S 5’ x 10’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

 

Graphic Only Includes:

  • (1) Custom Single-Sided Graphic with SEG hem

 

Material: Deco Fabric (non-stretch)

 

Print Process: Full Color Dye Sublimation

 

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

 

Warranty: One (1) year on graphics

 

Artwork Size:62″W x 122″H

 

Shipping Dimensions: 20″L x 10″W x 6″H

 

Shipping Weight:4 lbs

 

VAIL 60S 5 ft. x 10 ft. Frame Only

V99

Vail-60S 5′ x 10′ Frame Only. The VAIL-60S is a single-sided extrusion with a profile width of 60mm and has a solid outside finish. Because the back side of the VAIL-60S is short, it works especially well for wall mounting letting you affix the frame in multiple ways; however, the VAIL-60S is suitable for free-standing or hanging overhead as well. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).

Frame Includes:

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

 

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.

Hardware Setup: Take two VAIL-60S extrusions and slide ein Corner Connector; tighten. Repeat this three times.
Upgrade to Replace: VAIL Toolless Corner Connector

Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.

Warranty: Lifetime on frame

Frame Size: 60″W x 108″H x 2.36″D

Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

VAIL 60S 6 ft. x 9 ft. Single-Sided Graphic Package

V98

VAIL-60S 6′ x 9’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-60S is a single-sided extrusion with a profile width of 60mm. The VAIL-60S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).


Package Includes:

  • (1) 4-Sided Frame
  • (1) Custom Single-Sided Graphic (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-60S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 72″W x 108″H x 2.36″D 


Artwork Size: 74″W x 110″H 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

VAIL 60S 6 ft. x 9 ft. – Single-Sided Graphic Only

V97

Single-Sided Graphic Replacement for the Vail-60S 6’ x 9’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Graphic Only Includes:

  • (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)

Print Process: Full Color Dye Sublimation

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

Warranty: One (1) year on graphics

Artwork Size:74″W x 110″H

Shipping Dimensions: 20″L x 10″W x 6″H

Shipping Weight:4 lbs

VAIL 60S 6 ft. x 9 ft. Frame Only

V96

Vail-60S 6′ x 9′ Frame Only. The VAIL-60S is a single-sided extrusion with a profile width of 60mm and has a solid outside finish. Because the back side of the VAIL-60S is short, it works especially well for wall mounting letting you affix the frame in multiple ways; however, the VAIL-60S is suitable for free-standing or hanging overhead as well. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).

Frame Includes:

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

 

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.

Hardware Setup: Take two VAIL-60S extrusions and slide ein Corner Connector; tighten. Repeat this three times.
Upgrade to Replace: VAIL Toolless Corner Connector

Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.

Warranty: Lifetime on frame

Frame Size: 

Vail-60S 5′ x 8′ Frame Only. The VAIL-60S is a single-sided extrusion with a profile width of 60mm and has a solid outside finish. Because the back side of the VAIL-60S is short, it works especially well for wall mounting letting you affix the frame in multiple ways; however, the VAIL-60S is suitable for free-standing or hanging overhead as well. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Frame Includes:

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

 

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.

Hardware Setup: Take two VAIL-60S extrusions and slide ein Corner Connector; tighten. Repeat this three times.

Upgrade to Replace: VAIL Toolless Corner Connector

Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.

Warranty: Lifetime on frame

Frame Size: 72″W x 108″H x 2.36″D

Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

VAIL 60S 6 ft. x 10 ft. Single-Sided Graphic Package

V95

VAIL-60S 6′ x 10’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-60S is a single-sided extrusion with a profile width of 60mm. The VAIL-60S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).


Package Includes:

  • (1) 4-Sided Frame
  • (1) Custom Single-Sided Graphic (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-60S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 72″W x 120″H x 2.36″D 


Artwork Size: 74″W x 122″H 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

VAIL 60S 6 ft. x 10 ft. – Single-Sided Graphic Only

V94

Single-Sided Graphic Replacement for the Vail-60S 6’ x 10’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

 

Graphic Only Includes:

  • (1) Custom Single-Sided Graphic with SEG hem

 

Material: Deco Fabric (non-stretch)

 

Print Process: Full Color Dye Sublimation

 

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

 

Warranty: One (1) year on graphics

 

Artwork Size:74″W x 110″H

 

Shipping Dimensions: 20″L x 10″W x 6″H

 

Shipping Weight:4 lbs

VAIL 60S 6 ft. x 10 ft. Frame Only

V93

Vail-60S 6′ x 10′ Frame Only. The VAIL-60S is a single-sided extrusion with a profile width of 60mm and has a solid outside finish. Because the back side of the VAIL-60S is short, it works especially well for wall mounting letting you affix the frame in multiple ways; however, the VAIL-60S is suitable for free-standing or hanging overhead as well. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).

Frame Includes:

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

 

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.

Hardware Setup: Take two VAIL-60S extrusions and slide ein Corner Connector; tighten. Repeat this three times.
Upgrade to Replace: VAIL Toolless Corner Connector

Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.

Warranty: Lifetime on frame

Frame Size: 

Vail-60S 5′ x 8′ Frame Only. The VAIL-60S is a single-sided extrusion with a profile width of 60mm and has a solid outside finish. Because the back side of the VAIL-60S is short, it works especially well for wall mounting letting you affix the frame in multiple ways; however, the VAIL-60S is suitable for free-standing or hanging overhead as well. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Frame Includes:

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

 

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.

Hardware Setup: Take two VAIL-60S extrusions and slide ein Corner Connector; tighten. Repeat this three times.

Upgrade to Replace: VAIL Toolless Corner Connector

Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.

Warranty: Lifetime on frame

Frame Size: 72″W x 120″H x 2.36″D

Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

VAIL 60S 7 ft. x 9 ft. Single-Sided Graphic Package

V92

VAIL-60S 7′ x 9’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-60S is a single-sided extrusion with a profile width of 60mm. The VAIL-60S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).


Package Includes:

  • (1) 4-Sided Frame
  • (1) Custom Single-Sided Graphic (SEG hem)
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-60S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 84″W x 108″H x 2.36″D 


Artwork Size: 86″W x 110″H 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

VAIL 60S 7 ft. x 9 ft. Frame Only

V91

Vail-60S 7′ x 9′ Frame Only. The VAIL-60S is a single-sided extrusion with a profile width of 60mm and has a solid outside finish. Because the back side of the VAIL-60S is short, it works especially well for wall mounting letting you affix the frame in multiple ways; however, the VAIL-60S is suitable for free-standing or hanging overhead as well. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).

Frame Includes:

  • (1) 4-Sided Frame
  • (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

 

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.

Hardware Setup: Take two VAIL-60S extrusions and slide ein Corner Connector; tighten. Repeat this three times.
Upgrade to Replace: VAIL Toolless Corner Connector

Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.

Warranty: Lifetime on frame

Frame Size: 84″W x 108″H x 2.36″D

Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H