Vail-60S  10’ x 7’ Frame Only. The VAIL-60S  is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Frame Includes: 

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 10’ edge and one 7′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 108″W x 84″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

Vail-60S  10’ x 8’ Frame Only. The VAIL-60S  is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Frame Includes: 

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 10’ edge and one 8′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 108″W x 84″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

Vail-60S  10’ x 9’ Frame Only. The VAIL-60S  is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Frame Includes: 

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (5) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 10’ edge and one 9′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 120″W x 108″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

Vail-60S  10’ x 10’ Frame Only. The VAIL-60S  is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Frame Includes: 

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (5) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 10’ edge and one 10′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 120″W x 120″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

Single-Sided Graphic Replacement for the Vail-60S 10’ x 2’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Graphic Only Includes:

• (1) Custom Single-Sided Graphic with SEG hem
• Material: Deco Fabric (non-stretch)

Print Process: Full Color Dye Sublimation

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

Warranty: One (1) year on graphics

Artwork Size: 122″W x 26″H

Shipping Dimensions: (1) box 16″L x 12″W x 6″H
Shipping Weight: 4 lbs