Vail-120D 7’ x 9’ Frame Only. The VAIL-120D is a double-sided extrusion with a profile width of 120mm. This extrusion has a solid outside finish and is rigid due to its taller and reinforced spine. The thickest profile width we have to offer, VAIL-120D is especially good for free-standing large images (tall or wide) because it is more stable than the thinner profile widths; however, it can be wall mounted or hung overhead as well as well. Use fabric Silicone Edge Graphics (SEG) with this frame. When installing the fabric graphic, the keter can fit slightly more than 12mm deep and 3mm wide into the keter trough. This extrusion is compatible with edge-lights or ladder lights (can be backlit). 


Frame Includes:

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (2) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-120D extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 7’ edge and slide in Corner Connector; tighten. Repeat this three times. 


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 84″W x 108″H x 4.72″D 


Shipping Dimensions: (2) boxes 96″L x 7.25″W x 6.5″H & 73.25″L x 7.25″W x 6.5″H

Single-Sided Graphic Replacement for the Vail-60S 2’ x 7’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Graphic Only Includes:

• (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)

Print Process: Full Color Dye Sublimation

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

Warranty: One (1) year on graphics

Artwork Size: 26″W x 74″H

Shipping Dimensions: 16″L x 10″W x 6″H

Shipping Weight: 3 lbs

Double-Sided Graphic Replacement for the Vail-100D 3’ x 2’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.


Graphic Only Includes:

• (2) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Graphic Installation:Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Warranty: One (1) year on graphics 


Artwork Size: 38″W x 26″H 


Shipping Dimensions: 12″L x 9″W x 6″H 

Double-Sided Graphic Replacement for the Vail-100D 3’ x 3’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.


Graphic Only Includes: 

• (2) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Graphic Installation:Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Warranty: One (1) year on graphics 


Artwork Size: 38″W x 38″H 


Shipping Dimensions: 12″L x 9″W x 6″H 


Shipping Weight: 4 lbs

Double-Sided Graphic Replacement for the Vail-100D 3’ x 4’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.


Graphic Only Includes:

• (2) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Graphic Installation:Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Warranty: One (1) year on graphics


Artwork Size: 38″W x 50″H


Shipping Dimensions: 16″L x 10″W x 6″H


Shipping Weight: 6 lbs

Double-Sided Graphic Replacement for the Vail-100D 3’ x 5’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.


Graphic Only Includes:

• (2) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Graphic Installation:Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Warranty: One (1) year on graphics 


Artwork Size: 38″W x 62″H 


Shipping Dimensions: 16″L x 10″W x 6″H 


Shipping Weight: 6 lbs

Double-Sided Graphic Replacement for the Vail-100D 3’ x 6’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.


Graphic Only Includes:

• (2) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch) 




Print Process: Full Color Dye Sublimation 


Graphic Installation:Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Warranty: One (1) year on graphics 


Artwork Size: 38″W x 74″H 


Shipping Dimensions: 16″L x 10″W x 6″H 


Shipping Weight: 6 lbs

Double-Sided Graphic Replacement for the Vail-100D 3’ x 7’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.


Graphic Only Includes:

• (2) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Graphic Installation:Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Warranty: One (1) year on graphics 


Artwork Size: 38″W x 86″H 


Shipping Dimensions: 20″L x 12″W x 6″H 


Shipping Weight: 6 lbs

Single-Sided Graphic Replacement for the Vail-100D 2’ x 10’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.


Graphic Only Includes:

• (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Warranty: One (1) year on graphics


Artwork Size: 26″W x 112″H


Shipping Dimensions: (1) box 16″L x 12″W x 6″H


Shipping Weight: 4 lbs

Double-Sided Graphic Replacement for the Vail-100D 2’ x 10’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.


Graphic Only Includes:

• (2) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Graphic Installation:Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Warranty: One (1) year on graphics 


Artwork Size: 26″W x 112″H 


Shipping Dimensions: 20″L x 16″W x 6″H 


Shipping Weight: 8 lbs

Double-Sided Graphic Replacement for the Vail-100D 2’ x 3’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.


Graphic Only Includes:

• (2) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Graphic Installation:Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Warranty: One (1) year on graphics 


Artwork Size: 26″W x 38″H 


Shipping Dimensions: 12″L x 9″W x 6″H 

Vail-100D 2’ x 10’ Frame Only. The VAIL-100D is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-100D is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is compatible with edge-lights or ladder lights (can be backlit). 


Frame Includes: 

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (2) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-100D extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 10’ edge and one 2′ edge and slide in Corner Connector; tighten. Repeat this three times. 


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 120″W x 24″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

Double-Sided Graphic Replacement for the Vail-100D 2’ x 4’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.


Graphic Only Includes:

• (2) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Graphic Installation:Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Warranty: One (1) year on graphics 


Artwork Size:26″W x 50″H 


Shipping Dimensions: 16″L x 10″W x 6″H 


Shipping Weight: 4 lbs

Double-Sided Graphic Replacement for the Vail-100D 2’ x 5’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.


Graphic Only Includes:

• (2) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Graphic Installation:Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Warranty: One (1) year on graphics 


Artwork Size: 26″W x 62″H 


Shipping Dimensions: 16″L x 10″W x 6″H 


Shipping Weight: 6 lbs

Double-Sided Graphic Replacement for the Vail-100D 2’ x 7’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.


Graphic Only Includes:

• (2) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation 


Graphic Installation:Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Warranty: One (1) year on graphics 


Artwork Size: 26″W x 86″H 


Shipping Dimensions: 20″L x 12″W x 6″H 


Shipping Weight: 6 lbs

Double-Sided Graphic Replacement for the Vail-100D 2’ x 6’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.


Graphic Only Includes:

• (2) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Graphic Installation:Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 

Warranty: One (1) year on graphics 


Artwork Size: 26″W x 74″H 


Shipping Dimensions: 16″L x 10″W x 6″H 


Shipping Weight: 6 lbs

Double-Sided Graphic Replacement for the Vail-100D 2’ x 8’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.


Graphic Only Includes:

• (2) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation


Graphic Installation:Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Warranty: One (1) year on graphics 


Artwork Size: 26″W x 98″H 


Shipping Dimensions: 20″L x 12″W x 6″H 


Shipping Weight: 6 lbs

Double-Sided Graphic Replacement for the Vail-100D 2’ x 9’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.


Graphic Only Includes:

• (2) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Graphic Installation:Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Warranty: One (1) year on graphics 


Artwork Size: 26″W x 110″H 


Shipping Dimensions: 20″L x 16″W x 6″H 


Shipping Weight: 6 lbs

Vail-100D 2’ x 9’ Frame Only. The VAIL-100D is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-100D is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is compatible with edge-lights or ladder lights (can be backlit). 


Frame Includes:

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (2) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-100D extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 2′ edge and slide in Corner Connector; tighten. Repeat this three times. 


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 24″W x 108″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

Single-Sided Graphic Replacement for the Vail-100D 2’ x 9’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.


Graphic Only Includes:

• (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Warranty: One (1) year on graphics 


Artwork Size: 26″W x 110″H 


Shipping Dimensions: (1) box 16″L x 12″W x 6″H


Shipping Weight: 3 lbs

Vail-40D 9’ x 10’ Double-Sided Graphic Package. The VAIL-40D is a double-sided Resort Extrusion with a profile width of 40mm. The alternative extrusion in style to the ASPEN-40D, the VAIL-40D has a solid outside finish. It is especially great for wall mounting and hanging overhead because it is lightweight, but can be used with feet to stand independently as it is more stable than the VAIL-40S. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.)


Package Includes: 

• (1) 4-Sided Frame
• (2) Custom Single-Sided Graphics (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (5) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Backdrop, Photo-ops, Showrooms, Step & Repeat, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Hardware Setup: : To make one edge of the frame, take two cut VAIL-40D extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 10′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 120″H x 1.57″D


Artwork Size: 110″W x 122″H


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H

Vail-40D 9’ x 2’ Double-Sided Graphic Package. The VAIL-40D is a double-sided Resort Extrusion with a profile width of 40mm. The alternative extrusion in style to the ASPEN-40D, the VAIL-40D has a solid outside finish. It is especially great for wall mounting and hanging overhead because it is lightweight, but can be used with feet to stand independently as it is more stable than the VAIL-40S. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.) 


Package Includes:

• (1) 4-Sided Frame
• (2) Custom Single-Sided Graphics (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Backdrop, Photo-ops, Showrooms, Step & Repeat, Etc. 


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: : To make one edge of the frame, take two cut VAIL-40D extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 2′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors 


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 24″H x 1.57″D 


Artwork Size: 110″W x 26″H 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

Vail-40D 9’ x 3’ Double-Sided Graphic Package. The VAIL-40D is a double-sided Resort Extrusion with a profile width of 40mm. The alternative extrusion in style to the ASPEN-40D, the VAIL-40D has a solid outside finish. It is especially great for wall mounting and hanging overhead because it is lightweight, but can be used with feet to stand independently as it is more stable than the VAIL-40S. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.) 


Package Includes: 

• (1) 4-Sided Frame
• (2) Custom Single-Sided Graphics (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Backdrop, Photo-ops, Showrooms, Step & Repeat, Etc. 


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: : To make one edge of the frame, take two cut VAIL-40D extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 3′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors 


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 36″H x 1.57″D 


Artwork Size: 110″W x 38″H 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

Vail-40D 9’ x 4’ Double-Sided Graphic Package. The VAIL-40D is a double-sided Resort Extrusion with a profile width of 40mm. The alternative extrusion in style to the ASPEN-40D, the VAIL-40D has a solid outside finish. It is especially great for wall mounting and hanging overhead because it is lightweight, but can be used with feet to stand independently as it is more stable than the VAIL-40S. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.) 


Package Includes:

• (1) 4-Sided Frame
• (2) Custom Single-Sided Graphics (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Backdrop, Photo-ops, Showrooms, Step & Repeat, Etc. 


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: : To make one edge of the frame, take two cut VAIL-40D extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 4′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors 


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 48″H x 1.57″D 


Artwork Size: 110″W x 50″H 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

Vail-40D 9’ x 5’ Double-Sided Graphic Package. The VAIL-40D is a double-sided Resort Extrusion with a profile width of 40mm. The alternative extrusion in style to the ASPEN-40D, the VAIL-40D has a solid outside finish. It is especially great for wall mounting and hanging overhead because it is lightweight, but can be used with feet to stand independently as it is more stable than the VAIL-40S. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.) 


Package Includes:

• (1) 4-Sided Frame
• (2) Custom Single-Sided Graphics (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Backdrop, Photo-ops, Showrooms, Step & Repeat, Etc. 


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: : To make one edge of the frame, take two cut VAIL-40D extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 5′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors 


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 60″H x 1.57″D 


Artwork Size: 110″W x 62″H 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H

Vail-40D 9’ x 6’ Double-Sided Graphic Package. The VAIL-40D is a double-sided Resort Extrusion with a profile width of 40mm. The alternative extrusion in style to the ASPEN-40D, the VAIL-40D has a solid outside finish. It is especially great for wall mounting and hanging overhead because it is lightweight, but can be used with feet to stand independently as it is more stable than the VAIL-40S. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.) 


Package Includes:

• (1) 4-Sided Frame
• (2) Custom Single-Sided Graphics (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Backdrop, Photo-ops, Showrooms, Step & Repeat, Etc. 


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: : To make one edge of the frame, take two cut VAIL-40D extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 6′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors 


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 72″H x 1.57″D 


Artwork Size: 110″W x 74″H 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H

Vail-40D 9’ x 8’ Double-Sided Graphic Package. The VAIL-40D is a double-sided Resort Extrusion with a profile width of 40mm. The alternative extrusion in style to the ASPEN-40D, the VAIL-40D has a solid outside finish. It is especially great for wall mounting and hanging overhead because it is lightweight, but can be used with feet to stand independently as it is more stable than the VAIL-40S. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.) 


Package Includes:

• (1) 4-Sided Frame
• (2) Custom Single-Sided Graphics (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Backdrop, Photo-ops, Showrooms, Step & Repeat, Etc. 


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: : To make one edge of the frame, take two cut VAIL-40D extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 8′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors 


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 96″H x 1.57″D 


Artwork Size: 110″W x 98″H 


Shipping Dimensions: (2) boxes 96″L x 7.25″W x 6.5″H & 73.25″L x 7.25″W x 6.5″H

Vail-40D 9’ x 7’ Double-Sided Graphic Package. The VAIL-40D is a double-sided Resort Extrusion with a profile width of 40mm. The alternative extrusion in style to the ASPEN-40D, the VAIL-40D has a solid outside finish. It is especially great for wall mounting and hanging overhead because it is lightweight, but can be used with feet to stand independently as it is more stable than the VAIL-40S. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.)


Package Includes:

• (1) 4-Sided Frame
• (2) Custom Single-Sided Graphics (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Backdrop, Photo-ops, Showrooms, Step & Repeat, Etc. 


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: : To make one edge of the frame, take two cut VAIL-40D extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 7′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors 


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 84″H x 1.57″D 


Artwork Size: 110″W x 86″H 


Shipping Dimensions: (2) boxes 96″L x 7.25″W x 6.5″H & 73.25″L x 7.25″W x 6.5″H

Vail-40D 9’ x 9’ Double-Sided Graphic Package. The VAIL-40D is a double-sided Resort Extrusion with a profile width of 40mm. The alternative extrusion in style to the ASPEN-40D, the VAIL-40D has a solid outside finish. It is especially great for wall mounting and hanging overhead because it is lightweight, but can be used with feet to stand independently as it is more stable than the VAIL-40S. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.) 


Package Includes:

• (1) 4-Sided Frame
• (2) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (5) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Step & Repeat, Etc. 


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation


Hardware Setup: : To make one edge of the frame, take two cut VAIL-40D extrusions and, between, add Split Connector; tighten. Repeat this three times. Take two completed 9’ edges and slide in Corner Connector; tighten. Repeat this three times. Connect VAIL-40C to the other; tighten. Vertically insert ends of completed VAIL-40C into top and bottom of the frame; tighten. 


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 108″H x 1.57″D


Artwork Size: 110″W x 110″H


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H

Vail-60S  9’ x 3’ Frame Only. The VAIL-60S  is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Frame Includes: 

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 3′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 108″W x 36″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

Single-Sided Graphic Replacement for the Vail-60S 9’ x 3’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Graphic Only Includes:

• (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)

Print Process: Full Color Dye Sublimation

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

Warranty: One (1) year on graphics

Artwork Size: 110″W x 38″H

Shipping Dimensions: (1) box 16″L x 12″W x 6″H

Shipping Weight: 4 lbs

Vail-60S  9’ x 2’ Frame Only. The VAIL-60S  is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Frame Includes: 

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 2′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 108″W x 24″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

Vail-60S  9’ x 4’ Frame Only. The VAIL-60S  is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Frame Includes: 

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 4′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 108″W x 48″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

Vail-60S  9’ x 5’ Frame Only. The VAIL-60S  is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Frame Includes: 

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 5′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 108″W x 60″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

Vail-60S  9’ x 6’ Frame Only. The VAIL-60S  is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Frame Includes: 

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 6′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 108″W x 72″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

Vail-60S  9’ x 7’ Frame Only. The VAIL-60S  is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Frame Includes: 

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 7′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 108″W x 84″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

Vail-60S  9’ x 8’ Frame Only. The VAIL-60S  is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Frame Includes: 

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 8′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 108″W x 84″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

Vail-60S  9’ x 9’ Frame Only. The VAIL-60S  is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Frame Includes: 

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (5) VAIL Split Connectors (1 installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 9′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 108″W x 108″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

Vail-60S  9’ x 10’ Frame Only. The VAIL-60S  is a double-sided extrusion with a profile width of 100mm. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Frame Includes: 

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (5) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 10′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 108″W x 120″H x 3.94″D 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

Vail-60S 9’ x 2’ Single-Sided Graphic Package. Vail-60S  is a double-sided Resort Extrusion with a 60mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Partition Wall, Step & Repeat, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Hardware Setup: : To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 2’ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 24″H x 3.94″D


Artwork Size: 110″W x 38″H


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

Vail-60S 9’ x 4’ Single-Sided Graphic Package. Vail-60S  is a double-sided Resort Extrusion with a 60mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Partition Wall, Step & Repeat, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Hardware Setup: : To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 4’ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 48″H x 3.94″D


Artwork Size: 110″W x 38″H


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

Vail-60S 9’ x 6’ Single-Sided Graphic Package. Vail-60S  is a double-sided Resort Extrusion with a 60mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Partition Wall, Step & Repeat, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Hardware Setup: : To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 6’ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 72″H x 3.94″D


Artwork Size: 110″W x 38″H


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

Vail-60S 9’ x 8’ Single-Sided Graphic Package. Vail-60S  is a double-sided Resort Extrusion with a 60mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Partition Wall, Step & Repeat, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Hardware Setup: : To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 8’ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 96″H x 3.94″D


Artwork Size: 110″W x 38″H


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

Vail-60S 9’ x 7’ Single-Sided Graphic Package. Vail-60S  is a double-sided Resort Extrusion with a 60mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Partition Wall, Step & Repeat, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Hardware Setup: : To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 7’ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 84″H x 3.94″D


Artwork Size: 110″W x 38″H


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

Vail-60S 9’ x 9’ Single-Sided Graphic Package. Vail-60S  is a double-sided Resort Extrusion with a 60mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (5) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Partition Wall, Step & Repeat, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Hardware Setup: : To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 9’ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 108″H x 3.94″D


Artwork Size: 110″W x 38″H


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

Vail-60S 9’ x 10’ Single-Sided Graphic Package. Vail-60S  is a double-sided Resort Extrusion with a 60mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (5) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Partition Wall, Step & Repeat, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Hardware Setup: : To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 10’ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 120″H x 3.94″D


Artwork Size: 110″W x 38″H


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

Single-Sided Graphic Replacement for the Vail-60S 9’ x 2’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Graphic Only Includes:

• (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)

Print Process: Full Color Dye Sublimation

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

Warranty: One (1) year on graphics

Artwork Size: 110″W x 26″H

Shipping Dimensions: (1) box 16″L x 12″W x 6″H

Shipping Weight: 4 lbs

Single-Sided Graphic Replacement for the Vail-60S 9’ x 4’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Graphic Only Includes:

• (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)

Print Process: Full Color Dye Sublimation

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

Warranty: One (1) year on graphics

Artwork Size: 110″W x 50″H

Shipping Dimensions: (1) box 16″L x 12″W x 6″H

Shipping Weight: 4 lbs

Single-Sided Graphic Replacement for the Vail-60S 9’ x 5’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Graphic Only Includes:

• (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)

Print Process: Full Color Dye Sublimation

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

Warranty: One (1) year on graphics

Artwork Size: 110″W x 62″H

Shipping Dimensions: (1) box 16″L x 12″W x 6″H

Shipping Weight: 4 lbs

Single-Sided Graphic Replacement for the Vail-60S 9’ x 6’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Graphic Only Includes:

• (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)

Print Process: Full Color Dye Sublimation

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

Warranty: One (1) year on graphics

Artwork Size: 110″W x 74″H

Shipping Dimensions: (1) box 16″L x 12″W x 6″H

Shipping Weight: 4 lbs

Single-Sided Graphic Replacement for the Vail-60S 9’ x 7’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Graphic Only Includes:

• (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)

Print Process: Full Color Dye Sublimation

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

Warranty: One (1) year on graphics

Artwork Size: 110″W x 86″H

Shipping Dimensions: (1) box 16″L x 12″W x 6″H

Shipping Weight: 4 lbs

Single-Sided Graphic Replacement for the Vail-60S 9’ x 8’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Graphic Only Includes:

• (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)

Print Process: Full Color Dye Sublimation

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

Warranty: One (1) year on graphics

Artwork Size: 110″W x 98″H

Shipping Dimensions: (1) box 16″L x 12″W x 6″H

Shipping Weight: 4 lbs

Single-Sided Graphic Replacement for the Vail-60S 9’ x 9’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Graphic Only Includes:

• (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)

Print Process: Full Color Dye Sublimation

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

Warranty: One (1) year on graphics

Artwork Size: 110″W x 110″H

Shipping Dimensions: (1) box 16″L x 12″W x 6″H

Shipping Weight: 4 lbs

Single-Sided Graphic Replacement for the Vail-60S 9’ x 10’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Graphic Only Includes:

• (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)

Print Process: Full Color Dye Sublimation

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

Warranty: One (1) year on graphics

Artwork Size: 110″W x 122″H

Shipping Dimensions: (1) box 16″L x 12″W x 6″H

Shipping Weight: 4 lbs

VAIL-60S 2’ x 9’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-60S is a single-sided extrusion with a profile width of 60mm. The VAIL-60S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-60S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 24″W x 108″H x 2.36″D 


Artwork Size: 26″W x 108″H 


Shipping Dimensions:(1) box 96″L x 7.25″W x 6.5″H

Single-Sided Graphic Replacement for the Vail-60S 2’ x 9’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Graphic Only Includes:

• (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)

Print Process: Full Color Dye Sublimation

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

Warranty: One (1) year on graphics

Artwork Size: 26″W x 108″H

Shipping Dimensions: 16″L x 10″W x 6″H

Shipping Weight: 3 lbs

VAIL-60S 2’ x 10’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-60S is a single-sided extrusion with a profile width of 60mm. The VAIL-60S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-60S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 24″W x 120″H x 2.36″D 


Artwork Size: 26″W x 120″H 


Shipping Dimensions:(1) box 96″L x 7.25″W x 6.5″H

Vail-60S 2′ x 9′ Frame Only. The VAIL-60S is a single-sided extrusion with a profile width of 60mm and has a solid outside finish. Because the back side of the VAIL-60S is short, it works especially well for wall mounting letting you affix the frame in multiple ways; however, the VAIL-60S is suitable for free-standing or hanging overhead as well. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).

Frame Includes:

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.

Hardware Setup: Take two VAIL-60S extrusions and slide ein Corner Connector; tighten. Repeat this three times.
Upgrade to Replace: VAIL Toolless Corner Connector

Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.

Warranty: Lifetime on frame

Frame Size: 24″W x 108″H x 2.36″D

Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

Single-Sided Graphic Replacement for the Vail-60S 2’ x 10’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Graphic Only Includes:

• (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)

Print Process: Full Color Dye Sublimation

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

Warranty: One (1) year on graphics

Artwork Size: 26″W x 120″H

Shipping Dimensions: 16″L x 10″W x 6″H

Shipping Weight: 3 lbs

Vail-60S 2′ x 10′ Frame Only. The VAIL-60S is a single-sided extrusion with a profile width of 60mm and has a solid outside finish. Because the back side of the VAIL-60S is short, it works especially well for wall mounting letting you affix the frame in multiple ways; however, the VAIL-60S is suitable for free-standing or hanging overhead as well. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).

Frame Includes:

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.

Hardware Setup: Take two VAIL-60S extrusions and slide ein Corner Connector; tighten. Repeat this three times.
Upgrade to Replace: VAIL Toolless Corner Connector

Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.

Warranty: Lifetime on frame

Frame Size: 24″W x 108″H x 2.36″D

Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

Single-Sided Graphic Replacement for the Vail-60S 3’ x 9’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Graphic Only Includes:

• (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)

Print Process: Full Color Dye Sublimation

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

Warranty: One (1) year on graphics

Artwork Size: 38″W x 108″H

Shipping Dimensions: 16″L x 10″W x 6″H

Shipping Weight: 3 lbs

Vail-60S 3′ x 9′ Frame Only. The VAIL-60S is a single-sided extrusion with a profile width of 60mm and has a solid outside finish. Because the back side of the VAIL-60S is short, it works especially well for wall mounting letting you affix the frame in multiple ways; however, the VAIL-60S is suitable for free-standing or hanging overhead as well. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).

Frame Includes:

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.

Hardware Setup: Take two VAIL-60S extrusions and slide ein Corner Connector; tighten. Repeat this three times.
Upgrade to Replace: VAIL Toolless Corner Connector

Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.

Warranty: Lifetime on frame

Frame Size: 36″W x 108″H x 2.36″D

Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

Single-Sided Graphic Replacement for the Vail-60S 3’ x 10’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Graphic Only Includes:

• (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)

Print Process: Full Color Dye Sublimation

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

Warranty: One (1) year on graphics

Artwork Size: 38″W x 120″H

Shipping Dimensions: 16″L x 10″W x 6″H

Shipping Weight: 3 lbs

Vail-60S 3′ x 10′ Frame Only. The VAIL-60S is a single-sided extrusion with a profile width of 60mm and has a solid outside finish. Because the back side of the VAIL-60S is short, it works especially well for wall mounting letting you affix the frame in multiple ways; however, the VAIL-60S is suitable for free-standing or hanging overhead as well. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).

Frame Includes:

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.

Hardware Setup: Take two VAIL-60S extrusions and slide ein Corner Connector; tighten. Repeat this three times.
Upgrade to Replace: VAIL Toolless Corner Connector

Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.

Warranty: Lifetime on frame

Frame Size: 36″W x 120″H x 2.36″D

Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

VAIL-60S 4’ x 10’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-60S is a single-sided extrusion with a profile width of 60mm. The VAIL-60S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-60S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 48″W x 72″H x 2.36″D 


Artwork Size: 50″W x 98″H 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

Single-Sided Graphic Replacement for the Vail-60S 4’ x 10’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Graphic Only Includes:

• (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)

Print Process: Full Color Dye Sublimation

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

Warranty: One (1) year on graphics

Artwork Size:50″W x 120″H

Shipping Dimensions: 16″L x 12″W x 6″H

Shipping Weight: 4 lbs

Vail-60S 4′ x 10′ Frame Only. The VAIL-60S is a single-sided extrusion with a profile width of 60mm and has a solid outside finish. Because the back side of the VAIL-60S is short, it works especially well for wall mounting letting you affix the frame in multiple ways; however, the VAIL-60S is suitable for free-standing or hanging overhead as well. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).

Frame Includes:

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.

Hardware Setup: Take two VAIL-60S extrusions and slide ein Corner Connector; tighten. Repeat this three times.
Upgrade to Replace: VAIL Toolless Corner Connector

Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.

Warranty: Lifetime on frame

Frame Size: 48″W x 120″H x 2.36″D

Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

VAIL-60S 5′ x 9’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-60S is a single-sided extrusion with a profile width of 60mm. The VAIL-60S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-60S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 60″W x 108″H x 2.36″D 


Artwork Size: 62″W x 110″H 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

Single-Sided Graphic Replacement for the Vail-60S 5’ x 9’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Graphic Only Includes:

• (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)

Print Process: Full Color Dye Sublimation

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

Warranty: One (1) year on graphics

Artwork Size:62″W x 110″H

Shipping Dimensions: 20″L x 10″W x 6″H

Shipping Weight:4 lbs

VAIL-60S 4’ x 9’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-60S is a single-sided extrusion with a profile width of 60mm. The VAIL-60S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-60S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 48″W x 108″H x 2.36″D 


Artwork Size: 50″W x 110″H 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

Single-Sided Graphic Replacement for the Vail-60S 4’ x 9’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Graphic Only Includes:

• (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)

Print Process: Full Color Dye Sublimation

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

Warranty: One (1) year on graphics

Artwork Size:50″W x 110″H

Shipping Dimensions: 16″L x 12″W x 6″H

Shipping Weight: 4 lbs

Vail-60S 4′ x 9′ Frame Only. The VAIL-60S is a single-sided extrusion with a profile width of 60mm and has a solid outside finish. Because the back side of the VAIL-60S is short, it works especially well for wall mounting letting you affix the frame in multiple ways; however, the VAIL-60S is suitable for free-standing or hanging overhead as well. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).

Frame Includes:

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.

Hardware Setup: Take two VAIL-60S extrusions and slide ein Corner Connector; tighten. Repeat this three times.
Upgrade to Replace: VAIL Toolless Corner Connector

Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.

Warranty: Lifetime on frame

Frame Size: 48″W x 108″H x 2.36″D

Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

VAIL-60S 5′ x 10’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-60S is a single-sided extrusion with a profile width of 60mm. The VAIL-60S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-60S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 60″W x 120″H x 2.36″D 


Artwork Size: 62″W x 110″H 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

Vail-60S 5′ x 9′ Frame Only. The VAIL-60S is a single-sided extrusion with a profile width of 60mm and has a solid outside finish. Because the back side of the VAIL-60S is short, it works especially well for wall mounting letting you affix the frame in multiple ways; however, the VAIL-60S is suitable for free-standing or hanging overhead as well. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).

Frame Includes:

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.

Hardware Setup: Take two VAIL-60S extrusions and slide ein Corner Connector; tighten. Repeat this three times.
Upgrade to Replace: VAIL Toolless Corner Connector

Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.

Warranty: Lifetime on frame

Frame Size: 60″W x 108″H x 2.36″D

Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

Single-Sided Graphic Replacement for the Vail-60S 5’ x 10’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Graphic Only Includes:

• (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)

Print Process: Full Color Dye Sublimation

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

Warranty: One (1) year on graphics

Artwork Size:62″W x 122″H

Shipping Dimensions: 20″L x 10″W x 6″H

Shipping Weight:4 lbs

Vail-60S 5′ x 10′ Frame Only. The VAIL-60S is a single-sided extrusion with a profile width of 60mm and has a solid outside finish. Because the back side of the VAIL-60S is short, it works especially well for wall mounting letting you affix the frame in multiple ways; however, the VAIL-60S is suitable for free-standing or hanging overhead as well. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).

Frame Includes:

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.

Hardware Setup: Take two VAIL-60S extrusions and slide ein Corner Connector; tighten. Repeat this three times.
Upgrade to Replace: VAIL Toolless Corner Connector

Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.

Warranty: Lifetime on frame

Frame Size: 60″W x 108″H x 2.36″D

Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

VAIL-60S 6′ x 9’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-60S is a single-sided extrusion with a profile width of 60mm. The VAIL-60S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-60S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 72″W x 108″H x 2.36″D 


Artwork Size: 74″W x 110″H 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

Single-Sided Graphic Replacement for the Vail-60S 6’ x 9’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Graphic Only Includes:

• (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)

Print Process: Full Color Dye Sublimation

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

Warranty: One (1) year on graphics

Artwork Size:74″W x 110″H

Shipping Dimensions: 20″L x 10″W x 6″H

Shipping Weight:4 lbs

Vail-60S 6′ x 9′ Frame Only. The VAIL-60S is a single-sided extrusion with a profile width of 60mm and has a solid outside finish. Because the back side of the VAIL-60S is short, it works especially well for wall mounting letting you affix the frame in multiple ways; however, the VAIL-60S is suitable for free-standing or hanging overhead as well. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).

Frame Includes:

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.

Hardware Setup: Take two VAIL-60S extrusions and slide ein Corner Connector; tighten. Repeat this three times.
Upgrade to Replace: VAIL Toolless Corner Connector

Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.

Warranty: Lifetime on frame

Frame Size: 

Vail-60S 5′ x 8′ Frame Only. The VAIL-60S is a single-sided extrusion with a profile width of 60mm and has a solid outside finish. Because the back side of the VAIL-60S is short, it works especially well for wall mounting letting you affix the frame in multiple ways; however, the VAIL-60S is suitable for free-standing or hanging overhead as well. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Frame Includes:

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.

Hardware Setup: Take two VAIL-60S extrusions and slide ein Corner Connector; tighten. Repeat this three times.

Upgrade to Replace: VAIL Toolless Corner Connector

Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.

Warranty: Lifetime on frame

Frame Size: 72″W x 108″H x 2.36″D

Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

VAIL-60S 6′ x 10’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-60S is a single-sided extrusion with a profile width of 60mm. The VAIL-60S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-60S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 72″W x 120″H x 2.36″D 


Artwork Size: 74″W x 122″H 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

Single-Sided Graphic Replacement for the Vail-60S 6’ x 10’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Graphic Only Includes:

• (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)

Print Process: Full Color Dye Sublimation

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

Warranty: One (1) year on graphics

Artwork Size:74″W x 110″H

Shipping Dimensions: 20″L x 10″W x 6″H

Shipping Weight:4 lbs

Vail-60S 6′ x 10′ Frame Only. The VAIL-60S is a single-sided extrusion with a profile width of 60mm and has a solid outside finish. Because the back side of the VAIL-60S is short, it works especially well for wall mounting letting you affix the frame in multiple ways; however, the VAIL-60S is suitable for free-standing or hanging overhead as well. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).

Frame Includes:

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.

Hardware Setup: Take two VAIL-60S extrusions and slide ein Corner Connector; tighten. Repeat this three times.
Upgrade to Replace: VAIL Toolless Corner Connector

Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.

Warranty: Lifetime on frame

Frame Size: 

Vail-60S 5′ x 8′ Frame Only. The VAIL-60S is a single-sided extrusion with a profile width of 60mm and has a solid outside finish. Because the back side of the VAIL-60S is short, it works especially well for wall mounting letting you affix the frame in multiple ways; however, the VAIL-60S is suitable for free-standing or hanging overhead as well. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Frame Includes:

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.

Hardware Setup: Take two VAIL-60S extrusions and slide ein Corner Connector; tighten. Repeat this three times.

Upgrade to Replace: VAIL Toolless Corner Connector

Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.

Warranty: Lifetime on frame

Frame Size: 72″W x 120″H x 2.36″D

Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

VAIL-60S 7′ x 9’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-60S is a single-sided extrusion with a profile width of 60mm. The VAIL-60S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-60S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 84″W x 108″H x 2.36″D 


Artwork Size: 86″W x 110″H 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

Vail-60S 7′ x 9′ Frame Only. The VAIL-60S is a single-sided extrusion with a profile width of 60mm and has a solid outside finish. Because the back side of the VAIL-60S is short, it works especially well for wall mounting letting you affix the frame in multiple ways; however, the VAIL-60S is suitable for free-standing or hanging overhead as well. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).

Frame Includes:

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.

Hardware Setup: Take two VAIL-60S extrusions and slide ein Corner Connector; tighten. Repeat this three times.
Upgrade to Replace: VAIL Toolless Corner Connector

Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.

Warranty: Lifetime on frame

Frame Size: 84″W x 108″H x 2.36″D

Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

VAIL-60S 7′ x 10’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-60S is a single-sided extrusion with a profile width of 60mm. The VAIL-60S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-60S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 84″W x 120″H x 2.36″D 


Artwork Size: 86″W x 122″H 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

Single-Sided Graphic Replacement for the Vail-60S 7’ x 10’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Graphic Only Includes:

• (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)

Print Process: Full Color Dye Sublimation

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

Warranty: One (1) year on graphics

Artwork Size:86″W x 122″H

Shipping Dimensions: 20″L x 10″W x 6″H

Shipping Weight:4 lbs

Vail-60S 7′ x 10′ Frame Only. The VAIL-60S is a single-sided extrusion with a profile width of 60mm and has a solid outside finish. Because the back side of the VAIL-60S is short, it works especially well for wall mounting letting you affix the frame in multiple ways; however, the VAIL-60S is suitable for free-standing or hanging overhead as well. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).

Frame Includes:

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.

Hardware Setup: Take two VAIL-60S extrusions and slide ein Corner Connector; tighten. Repeat this three times.
Upgrade to Replace: VAIL Toolless Corner Connector

Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.

Warranty: Lifetime on frame

Frame Size: 84″W x 120″H x 2.36″D

Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

Single-Sided Graphic Replacement for the Vail-60S 8’ x 9’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Graphic Only Includes:

• (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)

Print Process: Full Color Dye Sublimation

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

Warranty: One (1) year on graphics

Artwork Size:98″W x 110″H

Shipping Dimensions: 20″L x 10″W x 6″H

Shipping Weight:4 lbs

Vail-60S 8′ x 9′ Frame Only. The VAIL-60S is a single-sided extrusion with a profile width of 60mm and has a solid outside finish. Because the back side of the VAIL-60S is short, it works especially well for wall mounting letting you affix the frame in multiple ways; however, the VAIL-60S is suitable for free-standing or hanging overhead as well. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).

Frame Includes:

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.

Hardware Setup: Take two VAIL-60S extrusions and slide ein Corner Connector; tighten. Repeat this three times.

Upgrade to Replace: VAIL Toolless Corner Connector

Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.

Warranty: Lifetime on frame

Frame Size: 96″W x 108″H x 2.36″D

Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

Single-Sided Graphic Replacement for the Vail-60S 8’ x 10’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Graphic Only Includes:

• (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)

Print Process: Full Color Dye Sublimation

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

Warranty: One (1) year on graphics

Artwork Size:98″W x 122″H

Shipping Dimensions: 20″L x 10″W x 6″H

Shipping Weight:4 lbs

Vail-60S 8′ x 10′ Frame Only. The VAIL-60S is a single-sided extrusion with a profile width of 60mm and has a solid outside finish. Because the back side of the VAIL-60S is short, it works especially well for wall mounting letting you affix the frame in multiple ways; however, the VAIL-60S is suitable for free-standing or hanging overhead as well. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).

Frame Includes:

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.

Hardware Setup: Take two VAIL-60S extrusions and slide ein Corner Connector; tighten. Repeat this three times.

Upgrade to Replace: VAIL Toolless Corner Connector

Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.

Warranty: Lifetime on frame

Frame Size: 96″W x 120″H x 2.36″D

Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

Vail-100D 6’ x 7’ Single-Sided Graphic Package. Vail-100D is a double-sided Resort Extrusion with a 100mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-100D is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is compatible with edge-lights or ladder lights (can be backlit). 


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Step & Repeat, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Hardware Setup: : Take two VAIL-100D extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 72″W x 84″H x 3.94″D


Artwork Size: 74″W x 86″H


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

Vail-40S 2’ x 3’ Frame Only. With a solid outside finish unlike the ASPEN-40D, the VAIL-40S is a single-sided extrusion with a profile width of 40mm. The VAIL-40S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. Use fabric Silicone Edge Graphics (SEG) with this frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.) 


Frame Includes: 

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: Take two VAIL-40S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 24″W x 36″H x 1.57″D


Shipping Dimensions: (1) box 49.75″L x 7.25″W x 6.5″H

Vail-40S 3’ x 8’ Frame Only. With a solid outside finish unlike the ASPEN-40D, the VAIL-40S is a single-sided extrusion with a profile width of 40mm. The VAIL-40S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. Use fabric Silicone Edge Graphics (SEG) with this frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.) 


Frame Includes:

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: Take two VAIL-40S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 36″W x 96″H x 1.57″D 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

VAIL-40S 3’ x 8’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-40S is a single-sided extrusion with a profile width of 40mm. The VAIL-40S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.)


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-40S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 36″W x 96″H x 1.57″D 


Artwork Size: 38″W x 98″H 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

VAIL-40S 5’ x 5’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-40S is a single-sided extrusion with a profile width of 40mm. The VAIL-40S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.)


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-40S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 60″W x 60″H x 1.57″D 


Artwork Size: 62″W x 62″H 


Shipping Dimensions: (1) box 73.25″L x 7.25″W x 6.5″H

VAIL-40S 7’ x 5’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-40S is a single-sided extrusion with a profile width of 40mm. The VAIL-40S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.)


Package Includes: 

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-40S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 84″W x 60″H x 1.57″D 


Artwork Size: 86″W x 62″H 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

Vail-40D 2’ x 3’ Frame Only. The VAIL-40D is a double-sided extrusion with a profile width of 40mm. The alternative extrusion in style to the ASPEN-40D, the VAIL-40D has a solid outside finish. It is especially great for wall mounting and hanging overhead because it is lightweight, but can be used with feet to stand independently as it is more stable than the VAIL-40S. Use fabric Silicone Edge Graphics (SEG) with this frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.) 


Frame Includes:

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: Take two VAIL-40D extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame 


Frame Size: 24″W x 36″H x 1.57″D 


Shipping Dimensions: (1) box 49.75″L x 7.25″W x 6.5″H

Vail-40D 2’ x 5’ Frame Only. The VAIL-40D is a double-sided extrusion with a profile width of 40mm. The alternative extrusion in style to the ASPEN-40D, the VAIL-40D has a solid outside finish. It is especially great for wall mounting and hanging overhead because it is lightweight, but can be used with feet to stand independently as it is more stable than the VAIL-40S. Use fabric Silicone Edge Graphics (SEG) with this frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.) 


Frame Includes: 

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: Take two VAIL-40D extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame


Frame Size: 24″W x 60″H x 1.57″D 


Shipping Dimensions: (1) box 73.25″L x 7.25″W x 6.5″H