Vail-120DB 8’ x 8’ Single-Sided Graphic Package. The VAIL-120DB is a double-sided extrusion with a profile width of 120mm. This extrusion has a solid outside finish and is just as thick as the VAIL-120D. This display is easy to mount on the wall because it is lightweight, but can also hang overhead or stand independently. VAIL-120DB is especially good for edge-lights since its spine is shorter, holding the lights very close to the graphic’s edges. When installing the fabric graphic, the keter can fit slightly more than 12mm deep and 3mm wide into the keter trough. This extrusion is compatible with edge-lights or ladder lights (can be backlit).


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Step & Repeat, Etc. 


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation 


Hardware Setup: : Take two VAIL-120DB extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector and Split Connectors 


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 96″W x 96″H x 4.72″D 


Artwork Size: 98″W x 98″H 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

Vail-120DB 9’ x 5’ Single-Sided Graphic Package. The VAIL-120DB is a double-sided extrusion with a profile width of 120mm. This extrusion has a solid outside finish and is just as thick as the VAIL-120D. This display is easy to mount on the wall because it is lightweight, but can also hang overhead or stand independently. VAIL-120DB is especially good for edge-lights since its spine is shorter, holding the lights very close to the graphic’s edges. When installing the fabric graphic, the keter can fit slightly more than 12mm deep and 3mm wide into the keter trough. This extrusion is compatible with edge-lights or ladder lights (can be backlit).


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Step & Repeat, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: : To make one edge of the frame, take two cut VAIL-120DB extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 5′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and Split Connectors 


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 60″H x 4.72″D 


Artwork Size: 110″W x 62″H 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H

Vail-120DB 10’ x 8’ Single-Sided Graphic Package. The VAIL-120DB is a double-sided extrusion with a profile width of 120mm. This extrusion has a solid outside finish and is just as thick as the VAIL-120D. This display is easy to mount on the wall because it is lightweight, but can also hang overhead or stand independently. VAIL-120DB is especially good for edge-lights since its spine is shorter, holding the lights very close to the graphic’s edges. When installing the fabric graphic, the keter can fit slightly more than 12mm deep and 3mm wide into the keter trough. This extrusion is compatible with edge-lights or ladder lights (can be backlit).


Package Includes:

• (1) 4-Sided Frame
• (2) Custom Single-Sided Graphics (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Step & Repeat, Etc. 


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: : To make one edge of the frame, take two cut VAIL-120DB extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 10’ edge and one 8′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and Split Connectors 


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 120″W x 96″H x 4.72″D 


Artwork Size: 122″W x 98″H 


Shipping Dimensions: (2) boxes 96″L x 7.25″W x 6.5″H & 73.25″L x 7.25″W x 6.5″H

Vail-40D 7’ x 10’ Single-Sided Graphic Package. The VAIL-40D is a double-sided Resort Extrusion with a profile width of 40mm. The alternative extrusion in style to the ASPEN-40D, the VAIL-40D has a solid outside finish. It is especially great for wall mounting and hanging overhead because it is lightweight, but can be used with feet to stand independently as it is more stable than the VAIL-40S. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.) 


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (2) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Backdrop, Photo-ops, Showrooms, Step & Repeat, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation 


Hardware Setup: : To make one edge of the frame, take two cut VAIL-40D extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 7’ edge and one 10′ edge and slide in Corner Connector; tighten. Repeat this three times. 


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors 


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 84″W x 120″H x 1.57″D 


Artwork Size: 86″W x 122″H 


Shipping Dimensions: (2) boxes 96″L x 7.25″W x 6.5″H & 73.25″L x 7.25″W x 6.5″H

Vail-40D 7’ x 10’ Double-Sided Graphic Package. The VAIL-40D is a double-sided Resort Extrusion with a profile width of 40mm. The alternative extrusion in style to the ASPEN-40D, the VAIL-40D has a solid outside finish. It is especially great for wall mounting and hanging overhead because it is lightweight, but can be used with feet to stand independently as it is more stable than the VAIL-40S. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.) 


Package Includes:

• (1) 4-Sided Frame
• (2) Custom Single-Sided Graphics (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (2) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Backdrop, Photo-ops, Showrooms, Step & Repeat, Etc. 


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Hardware Setup: : To make one edge of the frame, take two cut VAIL-40D extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 7’ edge and one 10′ edge and slide in Corner Connector; tighten. Repeat this three times. 


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors 


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size:84″W x 120″H x 1.57″D


Artwork Size: 86″W x 122″H


Shipping Dimensions: (2) boxes 96″L x 7.25″W x 6.5″H & 73.25″L x 7.25″W x 6.5″H

Double-Sided Graphic Replacement for the Vail-120D 2’ x 6’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.


Graphic Only Includes:

• (2) Custom Single-Sided Graphics with SEG hem

Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Graphic Installation:Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. Repeat on the other side.


Warranty: One (1) year on graphics


Artwork Size: 26″W x 74″H


Shipping Dimensions: (1) box 16″L x 10″W x 6″H


Shipping Weight: 6 lbs

Vail-60S 9’ x 5’ Single-Sided Graphic Package. Vail-60S  is a double-sided Resort Extrusion with a 60mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Partition Wall, Step & Repeat, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Hardware Setup: : To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 5’ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 60″H x 3.94″D


Artwork Size: 110″W x 38″H


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

VAIL-60S 8′ x 10’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-60S is a single-sided extrusion with a profile width of 60mm. The VAIL-60S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-60S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 96″W x 120″H x 2.36″D 


Artwork Size: 98″W x 122″H 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

VAIL-40S 3’ x 5’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-40S is a single-sided extrusion with a profile width of 40mm. The VAIL-40S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.)


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-40S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 36″W x 60″H x 1.57″D 


Artwork Size: 38″W x 62″H 


Shipping Dimensions: (1) box 73.25″L x 7.25″W x 6.5″H

VAIL-60S 3’ x 9’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-60S is a single-sided extrusion with a profile width of 60mm. The VAIL-60S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-60S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 36″W x 96″H x 2.36″D 


Artwork Size: 38″W x 98″H 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

VAIL-60S 3’ x 10’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-60S is a single-sided extrusion with a profile width of 60mm. The VAIL-60S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-60S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 36″W x 96″H x 2.36″D 


Artwork Size: 38″W x 98″H 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

Single-Sided Graphic Replacement for the Vail-60S 7’ x 9’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Graphic Only Includes:

• (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)

Print Process: Full Color Dye Sublimation

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

Warranty: One (1) year on graphics

Artwork Size:86″W x 110″H

Shipping Dimensions: 20″L x 10″W x 6″H

Shipping Weight:4 lbs

Vail-100D 2’ x 3’ Single-Sided Graphic Package. Vail-100D is a double-sided Resort Extrusion with a 100mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-100D is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is compatible with edge-lights or ladder lights (can be backlit). 


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Step & Repeat, Etc. 


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-100D extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 24″W x 36″H x 3.94″D 


Artwork Size: 26″W x 38″H 


Shipping Dimensions: (1) box 49.75″L x 7.25″W x 6.5″H

Vail-40S 5’ x 8’ Frame Only. With a solid outside finish unlike the ASPEN-40D, the VAIL-40S is a single-sided extrusion with a profile width of 40mm. The VAIL-40S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. Use fabric Silicone Edge Graphics (SEG) with this frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.) 


Frame Includes: 

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: Take two VAIL-40S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 60″W x 96″H x 1.57″D 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

VAIL-40S 6’ x 3’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-40S is a single-sided extrusion with a profile width of 40mm. The VAIL-40S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.)


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-40S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 72″W x 36″H x 1.57″D


Artwork Size: 74″W x 38″H 


Shipping Dimensions: (1) box 73.25″L x 7.25″W x 6.5″H

VAIL-40S 8’ x 8’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-40S is a single-sided extrusion with a profile width of 40mm. The VAIL-40S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.)


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-40S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 96″W x 96″H x 1.57″D


Artwork Size: 98″W x 98″H 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

Vail-40D 5’ x 5’ Frame Only. The VAIL-40D is a double-sided extrusion with a profile width of 40mm. The alternative extrusion in style to the ASPEN-40D, the VAIL-40D has a solid outside finish. It is especially great for wall mounting and hanging overhead because it is lightweight, but can be used with feet to stand independently as it is more stable than the VAIL-40S. Use fabric Silicone Edge Graphics (SEG) with this frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.)


Frame Includes:

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: Take two VAIL-40D extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 60″W x 60″H x 1.57″D 


Shipping Dimensions: (1) box 73.25″L x 7.25″W x 6.5″H

VAIL-60S 3’ x 6’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-60S is a single-sided extrusion with a profile width of 60mm. The VAIL-60S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-60S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 36″W x 72″H x 2.36″D 


Artwork Size: 38″W x 74″H 


Shipping Dimensions: (1) box 73.25″L x 7.25″W x 6.5″H

VAIL-40S 10’ x 8’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-40S is a single-sided extrusion with a profile width of 40mm. The VAIL-40S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.)


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Hardware Setup: To make one edge of the frame, take two cut VAIL-40S extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 10’ edge and one 8′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 120″W x 96″H x 1.57″D


Artwork Size: 112″W x 98″H


Shipping Dimensions: (2) boxes 96″L x 7.25″W x 6.5″H & 73.25″L x 7.25″W x 6.5″H

VAIL-60D 2’ x 3’ Double-Sided Graphic Package. The VAIL-60D is a double-sided extrusion with a profile width of 60mm. This extrusion has a solid outside finish. VAIL-60D is best for standing independently since the profile width is just wide enough to provide ultimate stability. This extrusion works great overhead too because the thick profile width really stands out. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).  


Package Includes:

• (1) 4-Sided Frame
• (2) Custom Single-Sided Graphics (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-60D extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. Repeat on the other side.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 24″W x 36″H x 2.36″D


Artwork Size: 26″W x 38″H 


Shipping Dimensions: (1) box 49.75″L x 7.25″W x 6.5″H

Vail-120D 5’ x 10’ Double-Sided Graphic Package. Vail-120D is a double-sided Resort Extrusion with a 120mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-120D is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is compatible with edge-lights or ladder lights (can be backlit). 


Package Includes:

• (1) 4-Sided Frame
• (2) Custom Single-Sided Graphics (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (2) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: To make one edge of the frame, take two cut VAIL-120D extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 10’ edge and one 5′ edge and slide in Corner Connector; tighten. Repeat this three times. 


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Toolless Split Connector. 


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. Repeat on the other side. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 60″W x 120″H x 4.72″D 


Artwork Size: 62″W x 122″H 


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H

Vail-100D 9’ x 8’ Single-Sided Graphic Package. Vail-100D is a double-sided Resort Extrusion with a 100mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-100D is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is compatible with edge-lights or ladder lights (can be backlit). 


Package Includes: 

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Partition Wall, Step & Repeat, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: : To make one edge of the frame, take two cut VAIL-100D extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 8′ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors 


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 96″H x 3.94″D


Artwork Size: 110″W x 98″H


Shipping Dimensions: (2) boxes 96″L x 7.25″W x 6.5″H & 73.25″L x 7.25″W x 6.5″H

Vail-100D 10’ x 8’ Single-Sided Graphic Package. Vail-100D is a double-sided Resort Extrusion with a 100mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-100D is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is compatible with edge-lights or ladder lights (can be backlit). 


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Partition Wall, Step & Repeat, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: : To make one edge of the frame, take two cut VAIL-100D extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 10’ edge and one 8’’ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors 


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 120″W x 96″H x 3.94″D 


Artwork Size: 122″W x 98″H 


Shipping Dimensions: (2) boxes 96″L x 7.25″W x 6.5″H & 73.25″L x 7.25″W x 6.5″H

Vail-100D 5’ x 8’ Double-Sided Graphic Package. Vail-100D is a double-sided Resort Extrusion with a 100mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-100D is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is compatible with edge-lights or ladder lights (can be backlit). 


Package Includes:

• (1) 4-Sided Frame
• (2) Custom Single-Sided Graphics (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (2) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Step & Repeat, Etc. 


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: : To make one edge of the frame, take two cut VAIL-120D extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 5’ edge and one 8’ edge and slide in Corner Connector; tighten. Repeat this three times. 


Upgrade to Replace: VAIL Toolless Corner Connector


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 60″W x 96″H x 3.94″D 


Artwork Size: 62″W x 98″H 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

Single-Sided Graphic Replacement for the Vail-100D 3’ x 7’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.

Graphic Only Includes:

• (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)

Print Process: Full Color Dye Sublimation

Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.

Warranty: One (1) year on graphics

Artwork Size: 38″W x 86″H

Shipping Dimensions: (1) box 16″L x 10″W x 6″H

Shipping Weight: 3 lbs

Vail-100D 4’ x 6’ Single-Sided Graphic Package. Vail-100D is a double-sided Resort Extrusion with a 100mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-100D is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is compatible with edge-lights or ladder lights (can be backlit). 


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Step & Repeat, Etc. 


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-100D extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 48″W x 72″H x 3.94″D 


Artwork Size: 50″W x 74″H 


Shipping Dimensions: (1) box 73.25″L x 7.25″W x 6.5″H

Vail-40S 4’ x 6’ Frame Only. With a solid outside finish unlike the ASPEN-40D, the VAIL-40S is a single-sided extrusion with a profile width of 40mm. The VAIL-40S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. Use fabric Silicone Edge Graphics (SEG) with this frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.) 


Frame Includes:

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: Take two VAIL-40S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 48″W x 72″H x 1.57″D


Shipping Dimensions: (1) box 73.25″L x 7.25″W x 6.5″H

VAIL-40S 3’ x 2’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-40S is a single-sided extrusion with a profile width of 40mm. The VAIL-40S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.)


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-40S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 36″W x 24″H x 1.57″D 


Artwork Size: 38″W x 26″H 


Shipping Dimensions: (1) box 49.75″L x 7.25″W x 6.5″H

VAIL-40S 5’ x 3’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-40S is a single-sided extrusion with a profile width of 40mm. The VAIL-40S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.)


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-40S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 60″W x 36″H x 1.57″D


Artwork Size: 62″W x 38″H


Shipping Dimensions: (1) box 73.25″L x 7.25″W x 6.5″H

VAIL-40S 7’ x 4’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-40S is a single-sided extrusion with a profile width of 40mm. The VAIL-40S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.)


Package Includes: 

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Hardware Setup: Take two VAIL-40S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 84″W x 48″H x 1.57″D


Artwork Size: 86″W x 50″H


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

VAIL-60S 3’ x 3’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-60S is a single-sided extrusion with a profile width of 60mm. The VAIL-60S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-60S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 36″W x 36″H x 2.36″D 


Artwork Size: 38″W x 38″H 


Shipping Dimensions: (1) box 49.75″L x 7.25″W x 6.5″H

VAIL-60S 8′ x 8’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-60S is a single-sided extrusion with a profile width of 60mm. The VAIL-60S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-60S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 96″W x 96″H x 2.36″D 


Artwork Size: 98″W x 98″H 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

Vail-120D 6’ x 8’ Single-Sided Graphic Package. Vail-120D is a double-sided Resort Extrusion with a 120mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-120D is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is compatible with edge-lights or ladder lights (can be backlit). 


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-120D extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 72″W x 96″H x 4.72″D 


Artwork Size: 74″W x 98″H 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

Vail-100D 3’ x 7’ Single-Sided Graphic Package. Vail-100D is a double-sided Resort Extrusion with a 100mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-100D is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is compatible with edge-lights or ladder lights (can be backlit). 


Package Includes: 

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-100D extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 36″W x 84″H x 3.94″D 


Artwork Size: 38″W x 86″H 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

Vail-120DB 5’ x 7’ Single-Sided Graphic Package. The VAIL-120DB is a double-sided extrusion with a profile width of 120mm. This extrusion has a solid outside finish and is just as thick as the VAIL-120D. This display is easy to mount on the wall because it is lightweight, but can also hang overhead or stand independently. VAIL-120DB is especially good for edge-lights since its spine is shorter, holding the lights very close to the graphic’s edges. When installing the fabric graphic, the keter can fit slightly more than 12mm deep and 3mm wide into the keter trough. This extrusion is compatible with edge-lights or ladder lights (can be backlit).


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Step & Repeat, Etc. 


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: : Take two VAIL-120DB extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connectors


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 60″W x 84″H x 4.72″D 


Artwork Size: 62″W x 86″H 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

VAIL-60S 8′ x 9’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-60S is a single-sided extrusion with a profile width of 60mm. The VAIL-60S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-60S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 96″W x 96″H x 2.36″D 


Artwork Size: 98″W x 98″H 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

Single-Sided Graphic Replacement for the Vail-40S 4’ x 6’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.


Graphic Only Includes:

• (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Graphic Installation:Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Warranty: One (1) year on graphics


Artwork Size: 50″W x 74″H


Shipping Dimensions: (1) box 16″L x 10″W x 6″H


Shipping Weight: 3 lbs

Vail-60D 6’ x 3’ Frame Only. The VAIL-60D is a double-sided extrusion with a profile width of 60mm. This extrusion has a solid outside finish. VAIL-60D is best for standing independently since the profile width is just wide enough to provide ultimate stability. This extrusion works great overhead too because the thick profile width really stands out. Use fabric Silicone Edge Graphics (SEG) with this frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).  


Frame Includes:

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: Take two VAIL-60D extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame


Frame Size: 72″W x 36″H x 2.36″D


Shipping Dimensions: (1) box 73.25″L x 7.25″W x 6.5″H

VAIL-60D 8’ x 8’ Single-Sided Graphic Package. The VAIL-60D is a double-sided extrusion with a profile width of 60mm. This extrusion has a solid outside finish. VAIL-60D is best for standing independently since the profile width is just wide enough to provide ultimate stability. This extrusion works great overhead too because the thick profile width really stands out. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit).


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-60D extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 96″W x 96″H x 2.36″D


Artwork Size: 98″W x 98″H


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

Vail-120D 4’ x 8’ Frame Only. The VAIL-120D is a double-sided extrusion with a profile width of 120mm. This extrusion has a solid outside finish and is rigid due to its taller and reinforced spine. The thickest profile width we have to offer, VAIL-120D is especially good for free-standing large images (tall or wide) because it is more stable than the thinner profile widths; however, it can be wall mounted or hung overhead as well as well. Use fabric Silicone Edge Graphics (SEG) with this frame. When installing the fabric graphic, the keter can fit slightly more than 12mm deep and 3mm wide into the keter trough. This extrusion is compatible with edge-lights or ladder lights (can be backlit). 


Frame Includes:

• (1) 4-Sided Frame
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Hardware Setup: Take two VAIL-120D extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame 


Frame Size: 48″W x 96″H x 4.72″D 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

Vail-40D 4’ x 4’ Double-Sided Graphic Package. The VAIL-40D is a double-sided Resort Extrusion with a profile width of 40mm. The alternative extrusion in style to the ASPEN-40D, the VAIL-40D has a solid outside finish. It is especially great for wall mounting and hanging overhead because it is lightweight, but can be used with feet to stand independently as it is more stable than the VAIL-40S. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.) 


Package Includes:

• (1) 4-Sided Frame
• (2) Custom Single-Sided Graphics (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Step & Repeat, Etc. 

Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Hardware Setup: : Take two VAIL-40D extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 48″W x 48″H x 1.57″D 


Artwork Size: 50″W x 98″H 


Shipping Dimensions: (1) box 49.75″L x 7.25″W x 6.5″H

Double-Sided Graphic Replacement for the Vail-120D 4’ x 4’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.


Graphic Only Includes:

• (2) Custom Single-Sided Graphics with SEG hem

Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Graphic Installation:Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. Repeat on the other side. 


Warranty: One (1) year on graphics 


Artwork Size: 50″W x 50″H 


Shipping Dimensions: (1) box 16″L x 10″W x 6″H


Shipping Weight: 6 lbs

Double-Sided Graphic Replacement for the Vail-120D 4’ x 6’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.


Graphic Only Includes:

• (2) Custom Single-Sided Graphics with SEG hem

Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Graphic Installation:Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. Repeat on the other side. 


Warranty: One (1) year on graphics 


Artwork Size: 50″W x 74″H 


Shipping Dimensions: (1) box 16″L x 10″W x 6″H


Shipping Weight: 6 lbs

Vail-60S 9’ x 3’ Single-Sided Graphic Package. Vail-60S  is a double-sided Resort Extrusion with a 60mm wide profile. This extrusion has a solid outside finish. Because the profile width is so thick, VAIL-60S  is especially good for free-standing large images (tall or wide) because it is more stable than the skinnier profile widths; however, it can be wall mounted or hung overhead. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. This extrusion is not compatible with lights (cannot be backlit). 


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench
• (3) VAIL Split Connectors (1 pre-installed on 1 VAIL-40C), (1) Torx Key
• (2) VAIL Key Locks (pre-installed), (1) 4mm Allen Wrench
• (2) VAIL-40C Support Extrusions

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Partition Wall, Step & Repeat, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation


Hardware Setup: : To make one edge of the frame, take two cut VAIL-60S  extrusions and, between, add Split Connector; tighten. Repeat this twice. Take one completed 9’ edge and one 3’ edge and slide in Corner Connector; tighten. Repeat this three times. Vertically insert ends of VAIL-40C into top and bottom of the frame; tighten.


Upgrade to Replace: VAIL Toolless Corner Connector and VAIL Split Connectors


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet.


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 108″W x 36″H x 3.94″D


Artwork Size: 110″W x 38″H


Shipping Dimensions: (2) boxes 73.25″L x 7.25″W x 6.5″H & 49.75″L x 7.25″W x 6.5″H

VAIL-40S 4’ x 6’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-40S is a single-sided extrusion with a profile width of 40mm. The VAIL-40S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.)


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch)


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-40S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 48″W x 72″H x 1.57″D 


Artwork Size: 50″W x 74″H 


Shipping Dimensions: (1) box 73.25″L x 7.25″W x 6.5″H

VAIL-40S 6’ x 6’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-40S is a single-sided extrusion with a profile width of 40mm. The VAIL-40S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.)


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation


Hardware Setup: Take two VAIL-40S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 72″W x 72″H x 1.57″D


Artwork Size: 74″W x 74″H 


Shipping Dimensions: (1) box 73.25″L x 7.25″W x 6.5″H

Single-Sided Graphic Replacement for the Vail-60D 8’ x 8’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.


Graphic Only Includes:

• (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Graphic Installation:Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Warranty: One (1) year on graphics 


Artwork Size: 98″W x 98″H 


Shipping Dimensions: (1) box 20″L x 10″W x 6″H


Shipping Weight: 4 lbs

Double-Sided Graphic Replacement for the Vail-60D 4’ x 7’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.


Graphic Only Includes:

• (2) Custom Single-Sided Graphics with SEG hem

Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation


Graphic Installation:Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. Repeat on the other side. 


Warranty: One (1) year on graphics 


Artwork Size: 50″W x 86″H 


Shipping Dimensions: (1) box 20″L x 12″W x 6″H


Shipping Weight: 6 lbs

Single-Sided Graphic Replacement for the Vail-40D 10’ x 9’. This edge-to-edge custom-made SEG fabric graphic has a sturdy edge hemmed with keter to help guide and snugly fit graphics into the frame. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough.


Graphic Only Includes:

• (1) Custom Single-Sided Graphic with SEG hem

Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Graphic Installation:Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides.


Warranty: One (1) year on graphics


Artwork Size: 122″W x 110″H 


Shipping Dimensions: (1) box 20″L x 16″W x 6″H


Shipping Weight: 5 lbs

VAIL-40S 2’ x 8’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-40S is a single-sided extrusion with a profile width of 40mm. The VAIL-40S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.)


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-40S extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics

Frame Size: 24″W x 96″H x 1.57″D 


Artwork Size: 26″W x 98″H 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H

VAIL-40S 8’ x 4’ Single-Sided Graphic Package. With a solid outside finish unlike the ASPEN-40D, the VAIL-40S is a single-sided extrusion with a profile width of 40mm. The VAIL-40S is rigid because its backside has a longer metal edge for reinforcement, making it especially great for wall mounting and hanging overhead. Plus, it is lightweight; however, for widths longer than 4ft., it is not recommended to be used as a free-standing display without a support because of its thin profile width. When installing the fabric graphic, the keter can fit 12mm deep and 3mm wide into the keter trough. Not compatible with lights (cannot be backlit.)


Package Includes:

• (1) 4-Sided Frame
• (1) Custom Single-Sided Graphic (SEG hem)
• (4) VAIL Corner Connectors, (16) Socket Screws, (1) 3mm Allen Wrench

Suggested Uses: Retail Stores, Restaurants, Art Galleries, Grand Openings, Trade Shows, Offices, Showrooms, Backdrop, Photo-ops, Step & Repeat, Partition Wall, Etc.


Material: Deco Fabric (non-stretch) 


Print Process: Full Color Dye Sublimation 


Hardware Setup: Take two VAIL-120D extrusions and slide in Corner Connector; tighten. Repeat this three times.


Upgrade to Replace: VAIL Toolless Corner Connector.


Graphic Installation: Transversely, push corners of graphic into the frame’s recessed groove. Then, starting midway on the frame going toward the corners, continue pushing in the straight edges of the graphic on all four sides. 


Accessories (sold separately): Wall Mounts, Ceiling Eye Hooks, Steel Base, Whistler Feet, Yeti Feet. 


Warranty: Lifetime on frame; one (1) year on graphics


Frame Size: 96″W x 48″H x 1.57″D 


Artwork Size: 98″W x 50″H 


Shipping Dimensions: (1) box 96″L x 7.25″W x 6.5″H